Beronet BN4S0 ISDN card and chan_misdn on Trixbox

I have with success installed the latest version of Trixbox on a server with a Beronet BN4S0 ISDN BRI card.



[root@asterisk1 ~]# uname -a



Linux asterisk1.local 2.6.9-34.0.1.EL #1 Mon Aug 21 07:40:56 CDT 2006 i686 i686 i386 GNU/Linux





The problem occurred when installing the latest version of misdn from http://www.beronet.com/downloads/install-misdn-mqueue.tar.gz on the Trixbox.



Installation went fin and the card could be found:



[root@asterisk1 ~]# /etc/init.d/misdn-init scan



[OK] found the following devices:

card=1,0x4

[ii] run "/usr/sbin/misdn-init config" to store this information to /etc/misdn-init.conf



“/etc/misdn-init.conf” and “/etc/asterisk/misdn.conf” was then configured.



… afterwards Asterisk was not able to start during reboot.





I have gathered following information:





The ISDN cad has been recognized on the PCI bus:



[root@asterisk1 ~]# lspci –v



06:03.0 ISDN controller: Cologne Chip Designs GmbH: Unknown device 08b4 (rev 01)

Subsystem: Cologne Chip Designs GmbH: Unknown device b560

Flags: medium devsel, IRQ 10

I/O ports at ccf8

Memory at fe3ff000 (32-bit, non-prefetchable) [size=4K]

Capabilities: [40] Power Management version 2





During bootup the ISDN card has been recognized but was not registered for some unknown reason:



[root@asterisk1 ~]# dmesg



…

Modular ISDN Stack core $Revision: 1.37 $

mISDNd: kernel daemon started (current:c23b12a0)

mISDNd: test event done

mISDN: HFC-multi driver Rev. 1.51

HFC-MULTI: Card 'HFC-4S Beronet Card' found, but not given by module's options, ignoring...

0 devices registered

…





The asterisk log shows problems starting chan_misdn module:



[root@asterisk1 ~]# tail /var/log/asterisk/full



…

Aug 21 11:39:32 VERBOSE[3271] logger.c: == Parsing '/etc/asterisk/skinny.conf':

Aug 21 11:39:32 VERBOSE[3271] logger.c: == Parsing '/etc/asterisk/skinny.conf': Found

Aug 21 11:39:32 VERBOSE[3271] logger.c: == Skinny listening on 0.0.0.0:2000

Aug 21 11:39:32 VERBOSE[3271] logger.c: == Registered channel type 'Skinny' (Skinny Client Control Protocol (Skinny))

Aug 21 11:39:32 VERBOSE[3271] logger.c: [chan_features.so]Aug 21 11:39:32 VERBOSE[3271] logger.c: [chan_features.so] => (Feature Proxy Channel)

Aug 21 11:39:32 VERBOSE[3271] logger.c: == Registered channel type 'Feature' (Feature Proxy Channel Driver)

Aug 21 11:39:32 VERBOSE[3271] logger.c: [chan_misdn.so]Aug 21 11:39:32 VERBOSE[3271] logger.c: [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri))

Aug 21 11:39:32 ERROR[3271] chan_misdn.c: Unable to initialize mISDN

Aug 21 11:39:32 WARNING[3271] loader.c: chan_misdn.so: load_module failed, returning -1

Aug 21 11:39:32 VERBOSE[3271] chan_misdn.c: -- Unregistering mISDN Channel Driver --

Aug 21 11:39:32 WARNING[3271] loader.c: Loading module chan_misdn.so failed!

…





Why do I get a “--ignore-install” when trying to start the chan_misdn module manually?



[root@asterisk1 ~]# /etc/init.d/misdn-init start

-----------------------------------------

Loading module(s) for your misdn-cards:

-----------------------------------------

modprobe --ignore-install hfcmulti type=0x4 protocol=0x22,0x22,0x22,0x22 layermask=0xf,0xf,0xf,0xf poll=128 pcm=-1 debug=222

modprobe mISDN_dsp debug=0x0 options=0 poll=128





What did go wrong or am I missing some setup?