- Mitglied seit
- 10 Jun 2007
- Beiträge
- 2,999
- Punkte für Reaktionen
- 7
- Punkte
- 38
hi,
hab auchmal den webkonfigurator ausprobiert, passwort war 1234:
-zugangspasswort geändert: OK
-ESSID geändert: OK
-konfiguration auf pc sichern: FEHLER
(aus/einschalten)
-DHCP lease time auf 1 woche verlängert (wegen der verbindungsabbrüche alle 24h)
-Auf Kanal 1 umgestellt: FEHLER, kein client verbindet mehr oder verliert nach etwa 10sek die assoziation, kann nur noch sporadisch per scan entdeckt werden:
CTRL-EVENT-CONNECTED - Connection to xxxxxxxxx completed (auth) [id=0 id_str=]
wpa_driver_wext_set_operstate: operstate 0->1 (UP)
WEXT: Operstate: linkmode=-1, operstate=6
EAPOL: External notification - portValid=1
EAPOL: External notification - EAP success=1
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state SUCCESS
EAP: EAP entering state DISABLED
EAPOL: SUPP_PAE entering state AUTHENTICATED
EAPOL: SUPP_BE entering state IDLE
RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'ath0' added
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
EAPOL: startWhen --> 0
...
(ca. 10sek)
...
RTM_NEWLINK: operstate=1 ifi_flags=0x1043 ([UP][RUNNING])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
Added BSSID xxxxxxxxxx into blacklist
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_madwifi_del_key: keyidx=0
wpa_driver_madwifi_del_key: keyidx=1
wpa_driver_madwifi_del_key: keyidx=2
wpa_driver_madwifi_del_key: keyidx=3
wpa_driver_madwifi_del_key: keyidx=0
State: COMPLETED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 1->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
(periode)
EDIT:
ok, nach paar mal ein/aus und pagingtaste hatte ich wenigstens n 15sek fenster und konnte den Kanal 5 wieder einsetzen, jetz gehtse wieder ok *puuh*
also: kanal darf nicht geändert werden, scheint woanders noch hardcoded zu sein.
hab auchmal den webkonfigurator ausprobiert, passwort war 1234:
-zugangspasswort geändert: OK
-ESSID geändert: OK
-konfiguration auf pc sichern: FEHLER
(aus/einschalten)
-DHCP lease time auf 1 woche verlängert (wegen der verbindungsabbrüche alle 24h)
-Auf Kanal 1 umgestellt: FEHLER, kein client verbindet mehr oder verliert nach etwa 10sek die assoziation, kann nur noch sporadisch per scan entdeckt werden:
CTRL-EVENT-CONNECTED - Connection to xxxxxxxxx completed (auth) [id=0 id_str=]
wpa_driver_wext_set_operstate: operstate 0->1 (UP)
WEXT: Operstate: linkmode=-1, operstate=6
EAPOL: External notification - portValid=1
EAPOL: External notification - EAP success=1
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state SUCCESS
EAP: EAP entering state DISABLED
EAPOL: SUPP_PAE entering state AUTHENTICATED
EAPOL: SUPP_BE entering state IDLE
RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'ath0' added
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
EAPOL: startWhen --> 0
...
(ca. 10sek)
...
RTM_NEWLINK: operstate=1 ifi_flags=0x1043 ([UP][RUNNING])
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
Added BSSID xxxxxxxxxx into blacklist
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_madwifi_del_key: keyidx=0
wpa_driver_madwifi_del_key: keyidx=1
wpa_driver_madwifi_del_key: keyidx=2
wpa_driver_madwifi_del_key: keyidx=3
wpa_driver_madwifi_del_key: keyidx=0
State: COMPLETED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 1->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
(periode)
EDIT:
ok, nach paar mal ein/aus und pagingtaste hatte ich wenigstens n 15sek fenster und konnte den Kanal 5 wieder einsetzen, jetz gehtse wieder ok *puuh*
also: kanal darf nicht geändert werden, scheint woanders noch hardcoded zu sein.
Zuletzt bearbeitet: