Hello to all,
I'm sorry but I cannot speak/write German, even with the help of Google Translation...
I have a SN4554 with the latest firmware and I wanted to receive call's from my landline and route them to my trixbox server.
Patton is capable of registering in trixbox but when I make a call to the the landline number I'll get a immediate busy tone.
With version 5.1 the majority of commands are different. I've tried searching in the forum but there only exists 4.2 examples.
Please advise.
Here is my config:
Best Regards,
Anthonws.
I'm sorry but I cannot speak/write German, even with the help of Google Translation...
I have a SN4554 with the latest firmware and I wanted to receive call's from my landline and route them to my trixbox server.
Patton is capable of registering in trixbox but when I make a call to the the landline number I'll get a immediate busy tone.
With version 5.1 the majority of commands are different. I've tried searching in the forum but there only exists 4.2 examples.
Please advise.
Here is my config:
Code:
#----------------------------------------------------------------#
# #
# SN4554/2BIS/EUI #
# R5.1 2008-01-18 SIP #
# 2008-04-07T14:13:18 #
# SN/00A0BA037039 #
# Generated configuration file #
# #
#----------------------------------------------------------------#
cli version 3.20
dns-client server 192.168.0.33
webserver port 80 language en
sntp-client
sntp-client server primary 192.168.0.34 port 123 version 4
system
ic voice 0
system
clock-source 1 bri 0 0
clock-source 2 bri 0 1
profile ppp default
profile tone-set default
profile voip default
codec 1 g729 rx-length 20 tx-length 20
codec 2 g711alaw64k rx-length 20 tx-length 20
codec 3 g711ulaw64k rx-length 20 tx-length 20
dejitter-mode static
dejitter-max-delay 120
profile pstn default
profile sip default
profile aaa default
method 1 local
method 2 none
context ip router
rtp-port-range 10000 10050
interface IF_IP_WAN
ipaddress 192.168.0.230 255.255.255.0
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
context cs switch
routing-table called-e164 RT_TO_SIP
route .T dest-interface IF_SIP
interface isdn IF_S0_00
route call dest-table RT_TO_SIP
interface sip IF_SIP
route call dest-service SER_HG_PSTN_FALLBACK
remote 192.168.0.210
local 192.168.0.230
service hunt-group SER_HG_PSTN_FALLBACK
drop-cause normal-unspecified
drop-cause no-circuit-channel-available
drop-cause network-out-of-order
drop-cause temporary-failure
drop-cause switching-equipment-congestion
drop-cause access-info-discarded
drop-cause circuit-channel-not-available
drop-cause resources-unavailable
route call 1 dest-interface IF_S0_00
context cs switch
no shutdown
authentication-service SER_AUTH_OB
username 8012 password aTQGEQSe8Vk= encrypted
location-service SER_LOC_CERT
domain 1 192.168.0.210 5060
identity 8012
authentication outbound
authenticate 1 authentication-service SER_AUTH_OB username 8012
registration outbound
register auto
context sip-gateway GW_SIP
interface IF_GW_WAN
bind interface IF_IP_WAN context router port 5060
context sip-gateway GW_SIP
bind location-service SER_LOC_CERT
no shutdown
port ethernet 0 0
bind interface IF_IP_WAN router
no shutdown
port bri 0 0
clock auto
encapsulation q921
q921
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_S0_00 switch
port bri 0 0
no shutdown
port bri 0 1
clock auto
encapsulation q921
q921
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side user
bchan-number-order ascending
port bri 0 1
shutdown
Best Regards,
Anthonws.