Code:
ROM VER: 1.0.3
CFG 01
Readà
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X
=======================================================================
Wireless ADSL Gateway DANUBE Loader v1.03.04 build May 15 2008 20:57:30
Arcadyan Technology Corporation
=======================================================================
MXIC MX29LV320ABTC bottom boot 16-bit mode found
Copying boot params.....DONE
Press Space Bar 3 times to enter command mode ...
Flash Checking Passed.
Unzipping firmware at 0x80002000 ... with AREA[2][ZIP 3]
[ZIP Extra] [ZIP 1] done
Ready to run firmware
In c_entry() function ...
install_exception
Co config = 80008483
[INIT] Interrupt ...
##### _ftext = 0x80002000
##### _fdata = 0x804F73A0
##### __bss_start = 0x805A3D90
##### end = 0x81BF9314
##### Backup Data from 0x804F73A0 to 0x81C01314~0x81CADD04 len 707056
##### Backup Data completed
##### Backup Data verified
[GPIO FLOW] SetGpio() Begin ..
[GPIO FLOW] SetGpio() End.
[INIT] System Log Pool startup ...
[INIT] MTinitialize ..
[INIT] usrclk
CPU Clock 333333334 Hz
mips_counter_frequency:166666667
r4k_offset: 00028b0a(166666)
init_US_counter : time1 = 260451 , time2 = 40260504, diff 40000053
US_counter = 48
cnt1 40984875 cnt2 40987142, diff 2267
Runtime code version: 1.07.000
System startup...
[INIT] Memory COLOR 0, 2548576 bytes ..
[INIT] Memory COLOR 1, 262144 bytes ..
[INIT] Memory COLOR 2, 5546928 bytes ..
InitCommSys: RESOURCE_BASE = 62, NUMRES = 640
InitCommSys: EVENT_BASE = 113, NUMEVT = 818
InitCommSys: MAILBOX_BASE = 6, NUMMBX = 64
rzMemory start: 0x80C5D5F0, end 0x81041700, size 4079888
Build Day = Dec 15 2008
>>>>set_MP_pass_Magic to 2
MXIC MX29LV320ABTC bottom boot 16-bit mode found
Set flash memory layout to Boot Parameters found !!!
HWOption set HWLAN : default PCI CLOCK External External interrupt PCI NUM 1
Bootcode version: v1.03.04
Serial number: J838010416
Hardware version: 01
pBootParams->password 59 71 6f (20)
Entered default password checking 0 8
fread_config_b> sizeof(struct III_Config_t) is 242652
MXIC MX29LV320ABTC bottom boot 16-bit mode found
fread_config_b> 7557 bytes read from flash
fread_config_b> 243163 bytes decompressed successfully.
-----------------------> Checking SysLog in Flash OK
-----------------------> Restore SysLog from Flash 490 bytes from 3b3e2
-----------------------> Restore Call Log from Flash 15 bytes from 3b5d3
DS_Tail ~ DS_Tail303_2 OK!
!!! Invalid wireless channel range 0 ~ 255
!!! Use default value 1 ~ 13
====xxx==============================-->425@-230;600(.4/.4/1,.4/3/1)
-->425@-230;30(.1/.25/1,.1/3/1)
-->600(.9/4.8)
-->600(.3/.5,.3/3)
-->600(.9/3.9)
check_WAN_switch returns 0
default route: 0.0.0.0
BufferInit:
BUF_HDR_SZ=160 BUF_ALIGN_SZ=4 BUFFER_OFFSET=384
BUF_BUFSZ0=544 BUF_BUFSZ1=4320
NUM_OF_B0=0 NUM_OF_B1=1400
BUF_POOL0_SZ=0 BUF_POOL1_SZ=6272000
sizeof(BUFFER0)=704,sizeof(BUFFER1)=4480
*BUF0=0x816883b8 *BUF1=0x8108cf98
Altgn *BUF0=0x816883c0 *BUF1=0x8108cfa0
End at BUF0:0x816883c0, BUF1:0x816883a0
BUF0[0]=0x816883c0 BUF1[0]=0x8108cfa0
buffer0 pointer init OK!
buffer1 pointer init OK!
[qm_lnk_init] CLOCKHZ=1000 ...
[qm_lnk_init] add if 3 into QM link 0
[qm_cbq_enable] no QM attached
[qm_cbq_detach] no QM is attached at link 0
f=3492148201/100000, ns_per_byte=1090005888/100000
New cls: id=0, bw=8080 ns/byte, maxd=0 ms,
maxb=32, minb=2, avgpktsz=0, maxpktsz=0,
offtime=1, parent=0, borrow=0
pri=0, maxidle=1, minidle=0,
maxq=96, clsfg=17
f=2002645667/100000, ns_per_byte=1083109375/100000
New cls: id=1, bw=808080 ns/byte, maxd=0 ms,
maxb=16, minb=1, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf62cc, borrow=81bf62cc
pri=5, maxidle=1, minidle=0,
maxq=48, clsfg=21
qm_cbq_attach(): cbqp->cbq_res=56
f=90439747/100000, ns_per_byte=1089990048/100000
New cls: id=2, bw=8162 ns/byte, maxd=0 ms,
maxb=32, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf62cc, borrow=81bf62cc
pri=5, maxidle=1, minidle=0,
maxq=48, clsfg=21
f=3846176767/100000, ns_per_byte=1072693248/100000
New cls: id=3, bw=799999999 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=0, maxidle=0, minidle=0,
maxq=96, clsfg=21
f=3846176767/100000, ns_per_byte=1072693248/100000
New cls: id=4, bw=799999999 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=1, maxidle=0, minidle=0,
maxq=48, clsfg=23
f=3846176767/100000, ns_per_byte=1072693248/100000
New cls: id=5, bw=799999999 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=2, maxidle=0, minidle=0,
maxq=48, clsfg=23
f=3846176767/100000, ns_per_byte=1072693248/100000
New cls: id=6, bw=799999999 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=3, maxidle=0, minidle=0,
maxq=48, clsfg=23
f=3846176767/100000, ns_per_byte=1072693248/100000
New cls: id=7, bw=799999999 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=4, maxidle=0, minidle=0,
maxq=48, clsfg=23
f=90439747/100000, ns_per_byte=1089990048/100000
New cls: id=8, bw=8162 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=6, maxidle=1, minidle=0,
maxq=48, clsfg=20
CLOCKHZ=1000
gConfig.Interface[0].IP_Addr = 127.0.0.1
gConfig.Interface[0].Subnet_Mask = 255.255.255.255
time = 08/01/2003, 00:00:00
TRAP(linkUp) : send ok!
Interface 0 ip = 127.0.0.1
gConfig.Interface[1].IP_Addr = 192.168.2.1
gConfig.Interface[1].Subnet_Mask = 255.255.255.0
vlan=0, vid=1, port_mask=0xf
DMA g_desc_list=0x80AF2100
MAC Address: 00:23:08:23:53:ba
time = 08/01/2003, 00:00:00
TRAP(linkUp) : send ok!
Interface 1 ip = 192.168.2.1
gConfig.Interface[2].IP_Addr = 0.0.0.0
gConfig.Interface[2].Subnet_Mask = 0.0.0.0
PCI clock 33.3MHz
cut-off PCI internal clock
DANUBE_GPIO_P1_ALTSEL0=547
DANUBE_GPIO_P1_ALTSEL1=0
DANUBE_GPIO_P1_DIR=91f6
[HWLAN] ifno=2 irno=7 port=0x00000000
RTMP_ADAPTER_mem : 8073d3e0, sizeof(RTMP_ADAPTER) 374272
rt2860_probe : should call pci_set_master() ???
should call pci_set_drvdata ???
time = 08/01/2003, 00:00:00
TRAP(linkUp) : send ok!
Interface 2 ip = 192.168.2.1
gConfig.Interface[3].IP_Addr = 0.0.0.0
gConfig.Interface[3].Subnet_Mask = 0.0.0.0
ppe: ATM init succeeded (firmware version 1.1.0.2.1.13)
ATM_UBR
Init SAR ifno:3 g_atm_vcc[0] CONN:1 VPI/VCI:1/32
MAC Address: 00:23:08:23:53:bb
Interface 3 ip = 0.0.0.0
gConfig.Interface[5].IP_Addr = 0.0.0.0
gConfig.Interface[5].Subnet_Mask = 0.0.0.0
IFLNK_PPPOE init : (Linkp)ifno = 5 idx = 2
IFLNK_PPPOE init : (Driverp)ifno = 5 idx = 3
Interface 5 ip = 0.0.0.0
gConfig.Interface[8].IP_Addr = 0.0.0.0
gConfig.Interface[8].Subnet_Mask = 0.0.0.0
[HWLAN] ifno=8 irno=7 port=0x00000000
time = 08/01/2003, 00:00:00
TRAP(linkUp) : send ok!
Interface 8 ip = 192.168.2.1
gConfig.Interface[9].IP_Addr = 0.0.0.0
gConfig.Interface[9].Subnet_Mask = 0.0.0.0
[HWLAN] ifno=9 irno=7 port=0x00000000
time = 08/01/2003, 00:00:00
TRAP(linkUp) : send ok!
Interface 9 ip = 192.168.2.1
gConfig.Interface[10].IP_Addr = 0.0.0.0
gConfig.Interface[10].Subnet_Mask = 0.0.0.0
[HWLAN] ifno=10 irno=7 port=0x00000000
time = 08/01/2003, 00:00:00
TRAP(linkUp) : send ok!
Interface 10 ip = 192.168.2.1
gConfig.Interface[11].IP_Addr = 0.0.0.0
gConfig.Interface[11].Subnet_Mask = 0.0.0.0
[HWLAN] ifno=11 irno=7 port=0x00000000
time = 08/01/2003, 00:00:00
TRAP(linkUp) : send ok!
Interface 11 ip = 192.168.2.1
ruleCheck()> Group: 0, Error: Useless rule index will be truncated
ruleCheck()> Group: 1, Error: Useless rule index will be truncated
ruleCheck()> Group: 2, Error: Useless rule index will be truncated
CBAC rule format check succeed !!
reqCBACBuf()> init match pool, Have: 1000
Memory Address: 0x81b9115c ~ 0x81b97ed8
reqCBACBuf()> init timeGap pool, Have: 10000
Memory Address: 0x81b97ed8 ~ 0x81bc8c2c
reqCBACBuf()> init sameHost pool, Have: 2000
Memory Address: 0x81bc8c2c ~ 0x81bd864c
CBAC rule pool initialized !!
[init_if] local_if_mask=0xf07
[init_if] local_wiredif_mask=0x2
[init_if] local_wirelessif_mask=0xf04
[init_if] localorVPN_if_mask=0xf07
1 set_timer: ti=0 type=1 ina[00000000] gid[00000000]
2 set_timer: ti=0 type=1 ina[00000000] gid[00000000]
3 set_timer: ti=0 type=1 ina[00000000] gid[00000000]
5 set_timer: ti=0 type=1 ina[00000000] gid[00000000]
8 set_timer: ti=0 type=1 ina[00000000] gid[00000000]
9 set_timer: ti=0 type=1 ina[00000000] gid[00000000]
10 set_timer: ti=0 type=1 ina[00000000] gid[00000000]
11 set_timer: ti=0 type=1 ina[00000000] gid[00000000]
Init NAT data structure
RUNTASK id=2 if_task if0...
RUNTASK id=3 if_task if1...
RUNTASK id=4 if_task if2...
RUNTASK id=5 if_task if3...
RUNTASK id=6 if_task if8...
RUNTASK id=7 if_task if9...
RUNTASK id=8 if_task if10...
RUNTASK id=9 if_task if11...
RUNTASK id=10 timer_task...
RUNTASK id=11 conn_mgr...
RUNTASK id=12 main_8021x...
Build Day = Dec 12 2008
gSetting.Rst_Time (12.12.2008, 12:45)-->year (2008),month (12),day (12),hour (1)
RUNTASK id=13 period_task...
========== ADSL Modem initialization OK ! ======
RUNTASK id=14 dhcp_daemon...
found signature: 78h 56h 34h 12h
ulImgLens=1290220, LENGTH[2]-12=3801076
length checking OK
[0] find End at 0xB018AC00 len=1290220
found signature: 78h 56h 34h 12h
ulImgLens=271340, LENGTH[2]-12=3801076
length checking OK
[1] find End at 0xB01CD000 len=271340
---[ ZIP1 head start in 0xB01CD400 ]---
found signature: 78h 56h 34h 12h
ulImgLens=150508, LENGTH[2]-12=3801076
length checking OK
[2] find End at 0xB01F1C00 len=150508
---[ ZIP1 head start in 0xB01F2000 ]---
found signature: 78h 56h 34h 12h
ulImgLens=417772, LENGTH[2]-12=3801076
length checking OK
[3] find End at 0xB0257C00 len=417772
Image[1] at 0xB0050000, len = 1290220
Image[2] at 0xB018B000, len = 271340
Image[3] at 0xB01CD400, len = 150508
Image[4] at 0xB01F2000, len = 417772
unzip for U/I from 0xb018b000 size 271340
Unzipping from B018B000 to 81D00000 ... [ZIP 3] [ZIP 0]
[ZIP Extra] [ZIP 1] [ZIP 1 2f534650] done
Uncompressed size = 1842350
drive start addr[0]=81d00000, [1]=81ec1cb0
httpd: listen at 192.168.2.1:80
httpd: listen at 192.168.2.1:443
RUNTASK httpd...
RUNTASK id=18 SSLClient ...
g_Client_Cert_Array=0x80c5d55c
RUNTASK id=19 dnsproxy...
RUNTASK id=20 dhcpd_mgmt_task...
UPnP is disabled
TR64 is enabled
TR64 Device initialize success! slot=21
[0] Allocate mailbox 6
[0] Allocate mailbox 7
FirstUseDate:0000-00-00T00:00:00
RUNTASK id=24 wscmain...
RUNTASK id=25 wsc_Send_eap_packet...
RUNTASK id=26 wsc_Send_UPNP_packet...
RUNTASK id=27 WSC_WaitUserAction_Task...
Starting Multitask...
run_project_task
RUNTASK id=28 CMV_task...
[0] Allocate resource 62, FreeResource = 1
fpiclk=83333333, rmc=16, fpiclk/rmc=5208333
ifx_ssc_clock = 5208333, baud=1000000
ifx_ssc_set_baud: br = 2
call ifx_ssc_init() = 0
call ifx_ssc_open() = 0
SPI_Init!
gptu: totally 6 16-bit timers/counters
Init timer (4) - OK
T_WLAN_INT=2
gSetting.CountryCode=0x8114
gSetting.Interface[T_WLAN_INT].Link_Type=1
RUNTASK id=30 apAppInit...
RUNTASK id=33 ScanMIH_task...
[qm_outbnd_bw_update] ...
[qm_cbq_resetclst] n_totalcls=9
aft rst: id=0, bw=8080 ns/byte, maxd=0 ms,
maxb=32, minb=2, avgpktsz=0, maxpktsz=0,
offtime=1, parent=0, borrow=0
pri=0, maxidle=1, minidle=0,
maxq=96, clsfg=17
aft rst: id=1, bw=808080 ns/byte, maxd=0 ms,
maxb=16, minb=1, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf62cc, borrow=81bf62cc
pri=5, maxidle=1, minidle=0,
maxq=48, clsfg=21
aft rst: id=2, bw=8162 ns/byte, maxd=0 ms,
maxb=32, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf62cc, borrow=81bf62cc
pri=5, maxidle=1, minidle=0,
maxq=48, clsfg=21
aft rst: id=3, bw=800000000 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=0, maxidle=0, minidle=0,
maxq=96, clsfg=21
aft rst: id=4, bw=800000000 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=1, maxidle=0, minidle=0,
maxq=48, clsfg=23
aft rst: id=5, bw=800000000 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=2, maxidle=0, minidle=0,
maxq=48, clsfg=23
aft rst: id=6, bw=800000000 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=3, maxidle=0, minidle=0,
maxq=48, clsfg=23
aft rst: id=7, bw=800000000 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=4, maxidle=0, minidle=0,
maxq=48, clsfg=23
aft rst: id=8, bw=8162 ns/byte, maxd=0 ms,
maxb=16, minb=4, avgpktsz=0, maxpktsz=0,
offtime=1, parent=81bf4ccc, borrow=81bf4ccc
pri=6, maxidle=1, minidle=0,
maxq=48, clsfg=20
init psock cnt=8000
[qm_cbq_enable] CBQ enabled at link: 0, DeQTask=34, wakeup event=10
low_pri_mtu: 2475
[qm_outbnd_bw_update] ok
ifno2dot1x_if[2]=0
ifno2dot1x_if[8]=81
ifno2dot1x_if[9]=82
ifno2dot1x_if[10]=83
ifno2dot1x_if[11]=84
dot1x_wireless_if_mask=0xf04
[reset_802dot1x] before loop waiting
ralink_init_flag 1 APReady 0
Danube MEI version:1.00.07
Unzip DSP firmware ...
Unzipping from B01CD400 to 81A3C800 ... [ZIP 1] [ZIP 1 49d78] VOICE_DRV_Init
Reset Duslic High begin
Wait VOIP_Init() finished...done
Uncompressed size = 302464
RUNTASK id=35 Atheros_NetTask ...
rt2860_open : should call request_irq ????????????????????????
rt2860_open 1
rt2860_open 2
rt2860_init 1
rt2860_init 2
rt2860_init 3
rt2860_init 6
rt2860_init 7
rt2860_init 8
rt2860_init 9
rt2860_init 10
update_img_hdr = A1A3C800
idx=0 mem_ptr=0xA1A3C800 size=65536
idx=1 mem_ptr=0xA1A4C800 size=65536
Reset Duslic end
IFX TAPI, version 3.6.1.10, (c) 2001-2008 Infineon Technologies AG
[37] Allocate mailbox 8
TAPI_init_task_queue: enter loop..8
sizeof(RT2860AP_DAT) : 1577
idx=2 mem_ptr=0xA1A5C800 size=65536
[31] Allocate resource 63, FreeResource = 2
[31] Allocate resource 64, FreeResource = 3
Channel=0
idx=3 mem_ptr=0xA1A6C800 size=65536
IFX VMMC device driver, version 1.2.1.10, (c) 2006-2008 Infineon Technologies AG
ifx_mps_init_module...
ifx_mps_init_structures request_irq 1 146
ifx_mps_init_structures request_irq 2 147
ifx_mps_init_structures request_irq 3 0 142
ifx_mps_init_structures request_irq 3 1 143
ifx_mps_init_structures request_irq 3 2 144
ifx_mps_init_structures request_irq 3 3 145
VMMC_Open : Major 122 Minor 10
ifx_tapi_open minorNum 10 majorNum 122
----------------------------> ifx_tapi_open dev 0 ch 0
[31] Allocate resource 65, FreeResource = 4
idx=4 mem_ptr=0xA1A7C800 size=40320
>>>>>>>>>>>>>>>>> TAPI_LL_Prepare_Dev vmmc_current_device 808436e0
[31] Allocate resource 66, FreeResource = 5
[31] Allocate resource 67, FreeResource = 6
[31] Allocate resource 68, FreeResource = 7
-----------------------VMMC_VOICE_POLL-----------------------
rtmp_read_wds_from_file() is called !!!
rtmp_read_wds_from_file : WDS disabled
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 1
-----------------------VMMC_TAPI_WAKEUP-----------------------
[31] Allocate resource 69, FreeResource = 8
[31] Allocate resource 70, FreeResource = 9
[31] Allocate resource 71, FreeResource = 10
[31] Allocate resource 72, FreeResource = 11
[31] Allocate resource 73, FreeResource = 12
[31] Allocate resource 74, FreeResource = 13
[31] Allocate resource 75, FreeResource = 14
[31] Allocate resource 76, FreeResource = 15
[31] Allocate resource 77, FreeResource = 16
[31] Allocate resource 78, FreeResource = 17
[31] Allocate resource 79, FreeResource = 18
[31] Allocate resource 80, FreeResource = 19
[31] Allocate resource 81, FreeResource = 20
[31] Allocate resource 82, FreeResource = 21
[31] Allocate resource 83, FreeResource = 22
[31] Allocate resource 84, FreeResource = 23
[31] Allocate resource 85, FreeResource = 24
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 2
[31] Allocate resource 86, FreeResource = 25
HT: Auto BA = Enable
HT: MCS = AUTO
HT: STBC = 1
HT: Tx Stream = 2
HT: Rx Stream = 2
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 3
[31] Allocate resource 87, FreeResource = 26
Magic No. in Boot Param check OK!!!
sould check E2PROM MAC ?????????????????
EEPROM_NIC1 123
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 4
[31] Allocate resource 88, FreeResource = 27
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 5
[31] Allocate resource 89, FreeResource = 28
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 6
[31] Allocate resource 90, FreeResource = 29
ADSL Firmware: 2.1.5.2.1.2 ATUR >>>>>>>>>>>>>>>>>(FW: 1.07.000)
[Annex B:0x4208 0x0]
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 7
[31] Allocate resource 91, FreeResource = 30
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 8
[31] Allocate resource 92, FreeResource = 31
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 9
VMMC_LL_Open, nDev 0, inode 0 mpsCh 1
ifx_mps_open, inode 1
g_drvpTapiDev 80c5b238
VMMC_Open --> 80a89948 80c5b238
i 0 VMMC_handle:80c5b238
VMMC_Open : Major 122 Minor 11
ifx_tapi_open minorNum 11 majorNum 122
----------------------------> ifx_tapi_open dev 0 ch 1
VMMC_LL_Open, nDev 0, inode 1 mpsCh 2
ifx_mps_open, inode 2
g_drvpTapiDev 80c58628
VMMC_Open --> 80a89948 80c58628
i 1 VMMC_handle:80c58628
VMMC_Open : Major 122 Minor 12
ifx_tapi_open minorNum 12 majorNum 122
----------------------------> ifx_tapi_open dev 0 ch 2
VMMC_LL_Open, nDev 0, inode 2 mpsCh 3
ifx_mps_open, inode 3
g_drvpTapiDev 80c58ba8
VMMC_Open --> 80a89948 80c58ba8
i 2 VMMC_handle:80c58ba8
VMMC_Open : Major 122 Minor 13
ifx_tapi_open minorNum 13 majorNum 122
----------------------------> ifx_tapi_open dev 0 ch 3
VMMC_LL_Open, nDev 0, inode 3 mpsCh 4
ifx_mps_open, inode 4
g_drvpTapiDev 80c59128
VMMC_Open --> 80a89948 80c59128
i 3 VMMC_handle:80c59128
VMMC_Open : Major 122 Minor 14
ifx_tapi_open minorNum 14 majorNum 122
----------------------------> ifx_tapi_open dev 0 ch 4
VMMC_LL_Open, nDev 0, inode 4 mpsCh 5
ifx_mps_open, inode 5
g_drvpTapiDev 80c596a8
VMMC_Open --> 80a89948 80c596a8
i 4 VMMC_handle:80c596a8
VMMC_Open : Major 122 Minor 15
ifx_tapi_open minorNum 15 majorNum 122
----------------------------> ifx_tapi_open dev 0 ch 5
VMMC_LL_Open, nDev 0, inode 5 mpsCh 6
ifx_mps_open, inode 6
g_drvpTapiDev 80c59c28
VMMC_Open --> 80a89948 80c59c28
i 5 VMMC_handle:80c59c28
VMMC_Open : Major 122 Minor 16
ifx_tapi_open minorNum 16 majorNum 122
----------------------------> ifx_tapi_open dev 0 ch 6
VMMC_LL_Open, nDev 0, inode 6 mpsCh 7
ifx_mps_open, inode 7
g_drvpTapiDev 80c5a1a8
VMMC_Open --> 80a89948 80c5a1a8
i 6 VMMC_handle:80c5a1a8
VMMC_Open : Major 122 Minor 17
ifx_tapi_open minorNum 17 majorNum 122
----------------------------> ifx_tapi_open dev 0 ch 7
VMMC_LL_Open, nDev 0, inode 7 mpsCh 8
g_drvpTapiDev 80c5a728
VMMC_Open --> 80a89948 80c5a728
i 7 VMMC_handle:80c5a728
VMMC_Open : Major 122 Minor 18
ifx_tapi_open minorNum 18 majorNum 122
----------------------------> ifx_tapi_open dev 0 ch 8
VMMC_LL_Open, nDev 0, inode 8 mpsCh 9
g_drvpTapiDev 80c5aca8
VMMC_Open --> 80a89948 80c5aca8
i 8 VMMC_handle:80c5aca8
===>
Set PCM I/F 0 VMMC_handle:80c5b238
[31] Allocate resource 93, FreeResource = 32
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 10
[31] Allocate resource 94, FreeResource = 33
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 11
[31] Allocate resource 95, FreeResource = 34
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 12
[31] Allocate resource 96, FreeResource = 35
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 13
[31] Allocate resource 97, FreeResource = 36
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 14
[31] Allocate resource 98, FreeResource = 37
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 15
[31] Allocate resource 99, FreeResource = 38
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 16
[31] Allocate resource 100, FreeResource = 39
>>>>>>>>>>>>>>>>>>>>>>>>> OS_GetEventNumber event number 17
ifx_mps_ioctl: FIO_MPS_DOWNLOAD...
Unzipping from B01F2000 to 817A6F84 ... [ZIP 1] [ZIP 1 a75cb796] done
Uncompressed size = 642816
IFX_MPS: Download firmware (size 642816 bytes)... ifx_mps_download_firmware: fi!
ok!
Version 11.0.0.1.0 up and running...
call ifx_mps_bufman_init
.Msleep at ch#13 to collect RX=0, RSSI=-127, CRC error =6, False CCA =18
ADSL> READY
set_VoIP__reg_led_timeout clear -1 t 1361
Msleep at ch#12 to collect RX=0, RSSI=-127, CRC error =36, False CCA =296
[reset_802dot1x] wireless module ready
[reset_802dot1x] 802.1Xv2 ready
.Msleep at ch#11 to collect RX=0, RSSI=-127, CRC error =4, False CCA =523
.Msleep at ch#10 to collect RX=0, RSSI=-127, CRC error =0, False CCA =33
MPS_ready() set ifx_mps_initialising=0===>
VMMC_Ioctl: Phone 1 IFX_TAPI_LINE_TYPE ok!
VMMC_Ioctl: Phone 1 IFXPHONE_SET_LINEFEED ok!
VMMC_Ioctl: Phone 1 IFX_TAPI_MAP_DATA_ADD ok!
Set PCM I/F 1 VMMC_handle:80c58628
===>
VMMC_Ioctl: Phone 2 IFX_TAPI_LINE_TYPE ok!
VMMC_Ioctl: Phone 2 IFXPHONE_SET_LINEFEED ok!
VMMC_Ioctl: Phone 2 IFX_TAPI_MAP_DATA_ADD ok!
Set PCM I/F 2 VMMC_handle:80c58ba8
===>
Set PCM I/F 3 VMMC_handle:80c59128
===>
Set PCM I/F 4 VMMC_handle:80c596a8
===>
Set PCM I/F 5 VMMC_handle:80c59c28
===>
Set PCM I/F 6 VMMC_handle:80c5a1a8
===>
Set PCM I/F 7 VMMC_handle:80c5a728
===>
Set PCM I/F 8 VMMC_handle:80c5aca8
Setting HOOK Related Parameters 0
Setting HOOKFLASH_TIME min 70 ms max 310 ms
Setting HOOKON_TIME min 370 max 370
Setting HOOK Related Parameters 1
Setting HOOK Related Parameters 2
Setting HOOK Related Parameters 3
RUNTASK id=38 VINETIC_DRV_Task...
[39] Allocate mailbox 9
RUNTASK id=39 VINETIC_T38_Task...
RUNTASK id=41 FXO_flash_task...
RUNTASK id=40 VOICE_API_task...
************** Enable ProDaaCheckInterrupt() detect 4041
.Msleep at ch#9 to collect RX=0, RSSI=-127, CRC error =1, False CCA =84
.Msleep at ch#8 to collect RX=0, RSSI=-127, CRC error =0, False CCA =40
Reset Duslic High begin
Reset Duslic end
ProDAAInitialize: begin now
ProDAAInitialize: Line-Side Device Status 40
Port 2 sytem-side revision 44, line-side revision 6
init_DTMF_data: time 5866
force_daa_offhook ch 2 onoff 1 time 5866
ProDaaOffhook 0 2 onoff 1
CID_Detect CH 2 onoff 0
VMMC_IFX_TAPI_LL_SIG_CID_RX_Stop ch 2
FXO_PolState_DTMFCID --> Disable DTMF CID
force_daa_offhook ch 2 onoff 0 time 5928
ProDaaOffhook 1 2 onoff 0
CID_Detect CH 2 onoff 1
VMMC_IFX_TAPI_LL_SIG_CID_RX_Start ch 2 hookmode 0
FXO_PolState_DTMFCID --> Detect Polarity Changed Enable DTMF CID
TEL_DRV_Init
TEL_DRV_StartDetVOIPHook
TEL_DRV_StartDetDTMF
TEL_DRV_StartDetCEDTone
TEL_DRV_StartDetVOIPHook
TEL_DRV_StartDetDTMF
TEL_DRV_StartDetCEDTone
TEL_DRV_InitTone
When * the value is 60000
When * the value is 60000
sys_voip_cfg->cpt.reorder = 425@-230;20(0.24/0.24/1)
TEL_DRV_TONE_REORDER duration = 480
. TEL_DRV_InitRing
>>>> STUN Setting <<<<
stun Enable : 0
stun Test Enable : 0
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
stun Server : "", IP : 0.0.0.0
stun Port : 3478
[31] Allocate resource 101, FreeResource = 40
[31] Allocate mailbox 10
VOICE_DRV_SetRxDataHookFunc
VOICE_DRV_SetRxDataHookFunc
TEL_MGR_Init
[31] Allocate resource 102, FreeResource = 41
tel_mgr_mutex=102
[31] Allocate mailbox 11
TEL_DM_Init
[31] Allocate resource 103, FreeResource = 42
******** TEL_LOG_UpdateCallRecord: No CallRecord Update, recNum:0 !!
[31] Allocate resource 104, FreeResource = 43
TEL_DRV_SetPhoneEvtHookFunc
TEL_DRV_SetLineEvtHookFunc
Msleep at ch#7 to collect RX=0, RSSI=-127, CRC error =0, False CCA =23
.Msleep at ch#6 to collect RX=0, RSSI=-127, CRC error =1, False CCA =28
Msleep at ch#5 to collect RX=0, RSSI=-127, CRC error =0, False CCA =149
TEL_MGR_VoiceChannelInit
TEL_MGR_SetVoiceChannel 1
TEL_MGR_SetVoiceChannel: ec mode is 16ms
TEL_MGR_SetPhoneEC
VOICE_DRV_SetEC ch 0 mode 32
TEL_MGR_SetPhoneVAD
VOICE_DRV_SetVAD 0
TEL_MGR_SetPhoneGain
VOICE_DRV_SetGain ch 0
VMMC_IFX_TAPI_LL_ALM_Volume_Set Ch 0 TxGain 0 RxGain -7
TEL_MGR_SetPhoneJitter
VOICE_DRV_SetJitter
Create task ISDN_GetCCBSCFStatus 43
SIP_CALLBACK_EnableDebug
SIP_CORE_EnableDebug
SIP_CORE_Init
[31] Allocate resource 105, FreeResource = 44
[31] Allocate mailbox 12
SIP_CORE_SetSipStatus
SIP_CORE_CreateTask
>>> SIP_CORE_Task
SIP_CORE_Set_Codec_Bandwidth : Bandwidth_Control = 1
SIP_CORE_Set_Codec_Bandwidth : ADSL / VDSL
SIP_CORE_Set_Codec_Bandwidth : Codec_Bandwidth[def_fax_call] = 106
SIP_CORE_Set_Codec_Bandwidth : Codec_Bandwidth[def_g711_call] = 106
SIP_CORE_Set_Codec_Bandwidth : Codec_Bandwidth[def_g726_32_call] = 85
SIP_CORE_Set_Codec_Bandwidth : Codec_Bandwidth[def_g726_24_call] = 64
SIP_CORE_Set_Codec_Bandwidth : Codec_Bandwidth[def_g729_call] = 43
SIP_CORE_Set_Codec_Bandwidth : Codec_Bandwidth[def_g722_call] = 106
[31] Allocate resource 106, FreeResource = 45
OK.
RUNTSK l2s3 31
RUNTSK l3l2 45
RUNTSK lll2 46
RUNTSK decrTout 47
ISDN: Q_L2S3:3, Q_L3L2:4, Q_LLL2:5
ISDN: Q_L2S3:3, Q_L3L2:4, Q_LLL2:5
Msleep at ch#3 to collect RX=0, RSSI=-127, CRC error =0, False CCA =34
Msleep at ch#2 to collect RX=0, RSSI=-127, CRC error =4, False CCA =799
Msleep at ch#1 to collect RX=0, RSSI=-127, CRC error =0, False CCA =31
Dirtyness = 0.0.0.0 - 0.0.1.1 - 2.2.11.2 - 11.2
pAd->CommonCfg.Channel = 1
rt2860_open 3
should Set up the Mac address ?????????
RT2860_WDS_Init --->
rt2860_open 4
rt2860_open 5
rt2860_open 6
ND 2 ???
Init_SSLServer> input listen_protocol=6, nListenPort=443
[17] ssld_conf_init> ssl server info:
[17] PrivateKey=
[17] MyCertificate=
[17] CaCertificate=
[17] SSL_method=31
[17] verify_mode=0
[17] cipher_suites=ALL:@STRENGTH:!kEDH
[17] tftp_server_ip=140.92.61.131
[17] fn_myCerttificate=ServCert.pem
[17] fn_privateKey=PrivKey.pem
[17] fn_caCertificate=CaCert.pem
[17] ssld_conf_init> ssl server info end:
PKCS12_PBE_add>
PKCS12_PBE_add> support RC4
PKCS12_PBE_add> support DES
PKCS12_PBE_add> support RC2
[17] pCtx=0x80c2e9ec in ssld_conf_init
ssld_ctx_reset_cert> this is pkcs12 type certificate
[17] ssld_ctx_reset_cert : re-LoadServerCertAndKey() ok!!
[17] ssld_ctx_reset_cert> re-LoadCACertificate( 1stCA ) ok!![17] ssld_conf_initk
[18] SSLClient> SSLClient() run
[18] sslc_conf_init> ssl client info:
[18] PrivateKey=
[18] MyCertificate=
[18] CaCertificate=
[18] SSL_method=31
[18] verify_mode=1
[18] cipher_suites=ALL:@STRENGTH:!kEDH
[18] tftp_server_ip=140.92.61.131
[18] fn_myCerttificate=ServCert.pem
[18] fn_privateKey=PrivKey.pem
[18] fn_caCertificate=CaCert.pem
[18] sslc_conf_init> ssl client info end:
[18] sslc_conf_init> pCtx=0x80c1cf40 in ssld_conf_init
[18] sslc_ctx_reset_cert> re-LoadCACertificate( 3rdCA ) ok!!
[18] sslc_ctx_reset_cert> re-LoadCACertificate( 2ndCA ) ok!!
[18] sslc_ctx_reset_cert> re-LoadCACertificate( 1stCA ) ok!!sslc_ctx_reset_certe
[18] sslc_ctx_reset_cert : re-LoadServerCertAndKey() ok!!
[18] sslc_conf_init> sslc_conf_init() ok
[18] SSLClient> want to bind socket for client application!
SSDP Initialization completed...
*********************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 2.01.1.DTM1.1, Dec 12 2008 18:48:55
*********************************************
Initializing stack...
---------in wsc init----------
----------sizeof(uint32)=4
----------sizeof(uint-long)=4
----------sizeof(uint32)=2
[PORTABLITY]:WscCreateThread--------------------
@#*@#*@#*EAP-WSC: Entered eap_wsc_init *#@*#@*#@
WSC_WaitUserAction:wait user action:2
ScanMIH_task> DHCP ip give: 192.168.2.100 ~ 199, range: 100
[HWLAN] [36] rapi_tmr_task running
WscCmd:ActualCBThreadProc: Started
>> Parse Service 'urn:dslforum-org:service:DeviceInfo:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:DeviceConfig:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:Layer3Forwarding:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:LANConfigSecurity:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:ManagementServer:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:Time:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:UserInterface:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:X_VoIP:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:LANHostConfigManagement:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:LANEthernetInterfaceConfig:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:WLANConfiguration:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:Hosts:1' : TRUE
>> Parse Device 'urn:dslforum-org:device:LANDevice:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:WANCommonInterfaceConfig:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:WANDSLInterfaceConfig:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:WANEthernetInterfaceConfig:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:WANDSLConnectionManagement:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:WANDSLLinkConfig:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:WANEthernetLinkConfig:1' : TRUE
>> Parse Service 'urn:dslforum-org:service:WANPPPConnection:1' : TRUE
>> Parse Device 'urn:dslforum-org:device:WANConnectionDevice:1' : TRUE
>> Parse Device 'urn:dslforum-org:device:WANDevice:1' : TRUE
>> Parse Device 'urn:dslforum-org:device:InternetGatewayDevice:1' : TRUETR64::T.
[htf_dbg] - OnlineActiveWirless() 1299
WirelessMode 9 BasicRate 15
AutochannelSelect 0 Channel 0
autoChannel : 1
NEW : channel 1, BW 1(40MHZ), EXTCHA 1(ABOVE)
stopWlanG ... start
[PORTABLITY]:WscCreateThread--------------------
WscCmd:ActualUIThreadProc: Started.
ActualUIThreadProc: wait q
stopWlanG .. done
>>>>>>>>>>>>>>>>>>>>>>tick 12624
MasterControl constructor
WscCmd::MC instantiated ok
[PORTABLITY]:WscCreateThread--------------------
[PORTABLITY]:pthread_mutex_init--------------------
CTransport Construction
[PORTABLITY]:WscCreateThread--------------------
In CTransport::ActualCBThreadProc
ActualCBThreadProc: Calling Dequeue
MC::Init: Init complete ok
WscCmd::MC intialized ok
WscCmd::Init ok, starting stack...
Info::ReadConfigFile:File open ok
******************uuid_p:0x000000000000000110000023082353ba*****
mp_deviceInfo->uuid[i]:
0-0-0-0-0-0-0-1-10-0-0-23-8-23-53-ba-
mp_deviceInfo->macAddr:00:23:08:23:53:BA
gSetting.dot1x.if_entry[0].enableWEP:0
authTypeFlags is 2 ,encrTypeFlags is 4 ,m_nwKey is SP1163BC041, key len is b
ssid is WLAN-235316
MC::SwitchModeOn: EModeApProxyRegistrar enter
RegistrarSM constructor
[PORTABLITY]:WscCreateThread--------------------
RegistrarSM constructor
[PORTABLITY]:WscCreateThread--------------------
[PORTABLITY]:pthread_mutex_init--------------------
MC::SetBeaconIE: call to trans->SetBeaconIE() ok
MC::SetProbeRespIE: call to trans->SetProbeRespIE() ok
©§©§
mp_deviceInfo->authTypeFlags:2
mp_deviceInfo->encrTypeFlags:4
*******build M1 start**********
RPROTO: BuildMessageM1_For_REG built: -2136365216 bytes
*******build M1 end**********
after InitializeSM....
in startMonitor....
CInbEap Construction
Sizeof(WSC_NOTIFY_DATA) = -2136365120
---test--sizeof(WSC_NOTIFY_DATA) = 36
[PORTABLITY]:WscCreateEvent--------------------
Entered udp_open
Socket open successful, sd: -2136365136
Entered udp_open
Socket open successful, sd: -2136365136
Entered udp_bind
Binding successful for socket [-2136365152]
[PORTABLITY]:WscCreateThread--------------------
In CInbEap::StaticRecvThread
CInbEap::ActualRecvThread Started
Entered udp_read
exit StartMonitor TRANSPORT_TYPE_UPNP_DEV
in startMonitor....
CInbUPnPDev Construction
Entered udp_open
Socket open successful, sd: -2136365136
Entered udp_open
Socket open successful, sd: -2136365136
Entered udp_bind
Binding successful for socket [-2136365152]
CInbUPnPDev StartMonitor
[PORTABLITY]:WscCreateThread--------------------
exit switch_mode
MC::SwitchModeOn: Exit
MC::StartStack: Informing app of mode
In CInbUPnPDev::StaticUPnPThread
end UPnPCreateMicroStack
Entered udp_read
WscCmd::CallbackProc Enqueue done
MC::SwitchModeOn: Done callback
exit wscmain
WscCmd:ActualCBThreadProc: CB_MAIN_PUSH_MODE recd
******* MODE: AP with built-in Registrar and UPnP Proxy *******
*******p_header->eType:5
LCB_MENU_AP_PROXY_REGISTRAR
**************b_tryAgain:1
Options:
0. Quit
1. Configure Client
2. Configure Client via push-button
Enter selection:
ADSL Firmware: 2.1.5.2.1.2 ATUR >>>>>>>>>>>>>>>>>(FW: 1.07.000)
[Annex B:0x4208 0x0]
ADSL> READY
set_VoIP__reg_led_timeout clear -1 t 61476
Zitieren
Zitat von byteeater
für den sx541 auch nen arcadyan produkt, hat sich nach bischen suchen die smc 7908vowbrb firmware gefunden, die prima auf der hütte rennt....
