Hallo,
hier kurz mein Aufbau:
Smartnode 4639 mit SIP-Account, 4 Sprachkanäle, 30 Rufnummern. An BRI0 hängt eine alte AGFEO AS33.
Anrufe funktionieren mit dieser Config wunderbar:
Jetzt habe ich aber an der AGFEO 2 Telefone (Nebenstelle 11 und 12). Telefon1 geht mit XXXXX11 aus der AGFEO auf die Patton und Telefon2 mit XXXXX12. Zum jetzigen zeitpunkt wird alles zu XXXXX10 von der Patton übersetzt und raus telefoniert. Eingehende Anrufe auf der XXXXX11 und XXXXX12 sind auf der AGFEO auch schon programmiert, aber von der Patton werden alle Anrufe bisher mit XXXXX10 an die AGFEO weitergegeben.
Hier ist auch mein Problem, stehe zur Zeit, glaube ich, ziemlich auf dem Schlauch. Wie bringe ich der Patton bei, dass sie eingehende Anrufe auf 07XXX/XXXXX11 oder XXXXX11 auch mit dieser Nummer an die AGFEO weiter gibt (Entsprechendes mit der XXXXX12). Also, dass die Rufnummernverwaltung komplett die AGFEO übernehmen kann.
Wäre nett, wenn mir jemand von euch hier behilflich sein könnte.
Danke im Voraus.
hier kurz mein Aufbau:
Smartnode 4639 mit SIP-Account, 4 Sprachkanäle, 30 Rufnummern. An BRI0 hängt eine alte AGFEO AS33.
Anrufe funktionieren mit dieser Config wunderbar:
Code:
#----------------------------------------------------------------#
# #
# SN4639/5BIS #
# R6.1 2012-05-09 H323 SIP BRI #
# 2012-07-17T09:18:42 #
# SN/XXX #
# Generated configuration file #
# #
#----------------------------------------------------------------#
cli version 3.20
administrator admin password XXX encrypted
clock local default-offset +00:00
dns-client server XX.XX.XX.XX
dns-client server XX.XX.XX.XX
dns-relay
webserver port 80 language en
sntp-client
sntp-client server primary XX.XX.XX.XX port 123 version 4
system
ic voice 0
low-bitrate-codec g729
system
clock-source 1 bri 0 0
clock-source 2 bri 0 1
clock-source 3 bri 0 2
clock-source 4 bri 0 3
clock-source 5 bri 0 4
profile napt NAPT_WAN
profile ppp default
profile tone-set default
profile voip default
codec 1 g711alaw64k rx-length 20 tx-length 20
codec 2 g711ulaw64k rx-length 20 tx-length 20
profile pstn default
profile sip default
no autonomous-transitioning
profile dhcp-server DHCPS_LAN
network 192.168.1.0 255.255.255.0
include 1 192.168.1.10 192.168.1.99
lease 2 hours
default-router 1 192.168.1.1
domain-name-server 1 192.168.1.1
profile aaa default
method 1 local
method 2 none
context ip router
interface WAN
ipaddress XX.XX.XX.XX 255.255.255.248
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
interface LAN
ipaddress 192.168.1.1 255.255.255.0
tcp adjust-mss rx mtu
tcp adjust-mss tx mtu
context ip router
dhcp-server use profile DHCPS_LAN
route 0.0.0.0 0.0.0.0 XX.XX.XX.XX 0
context cs switch
routing-table called-e164 RT_TO_SIP
route T dest-interface IF_SIP
interface isdn IF_ISDN
route call dest-table RT_TO_SIP
interface sip IF_SIP
bind context sip-gateway GW_SIP
route call dest-interface IF_ISDN
remote sip.XXX.de
address-translation outgoing-call from-header user-part fix 07XXXXXXX10 host-part call
address-translation incoming-call called-e164 fix XXXXX10
context cs switch
no shutdown
authentication-service SER_AUTH_OB
realm 1 sip.XXX.de
username 0XXXXXXXX10 password XXX encrypted
location-service SER_LOC_CERT
imperative foreign
domain 1 sip.XXX.de
identity 07XXXXXXXX10
authentication outbound
authenticate 1 authentication-service SER_AUTH_OB username 07XXXXXXX10
registration outbound
registrar sip.XXX.de
lifetime 60
register auto
context sip-gateway GW_SIP
interface IF_GW_SIP
bind interface WAN context router port 5060
context sip-gateway GW_SIP
bind location-service SER_LOC_CERT
no shutdown
port ethernet 0 0
medium auto
encapsulation ip
bind interface WAN router
no shutdown
port ethernet 0 1
medium auto
encapsulation ip
bind interface LAN router
no shutdown
port bri 0 0
clock auto
power-feed
encapsulation q921
q921
permanent-layer2
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side net
bchan-number-order ascending
encapsulation cc-isdn
bind interface IF_ISDN switch
port bri 0 0
no shutdown
port bri 0 1
clock auto
encapsulation q921
q921
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side net
bchan-number-order ascending
port bri 0 1
shutdown
port bri 0 2
clock auto
encapsulation q921
q921
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side net
bchan-number-order ascending
port bri 0 2
shutdown
port bri 0 3
clock auto
encapsulation q921
q921
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side net
bchan-number-order ascending
port bri 0 3
shutdown
port bri 0 4
clock auto
encapsulation q921
q921
uni-side auto
encapsulation q931
q931
protocol dss1
uni-side net
bchan-number-order ascending
port bri 0 4
shutdown
Jetzt habe ich aber an der AGFEO 2 Telefone (Nebenstelle 11 und 12). Telefon1 geht mit XXXXX11 aus der AGFEO auf die Patton und Telefon2 mit XXXXX12. Zum jetzigen zeitpunkt wird alles zu XXXXX10 von der Patton übersetzt und raus telefoniert. Eingehende Anrufe auf der XXXXX11 und XXXXX12 sind auf der AGFEO auch schon programmiert, aber von der Patton werden alle Anrufe bisher mit XXXXX10 an die AGFEO weitergegeben.
Hier ist auch mein Problem, stehe zur Zeit, glaube ich, ziemlich auf dem Schlauch. Wie bringe ich der Patton bei, dass sie eingehende Anrufe auf 07XXX/XXXXX11 oder XXXXX11 auch mit dieser Nummer an die AGFEO weiter gibt (Entsprechendes mit der XXXXX12). Also, dass die Rufnummernverwaltung komplett die AGFEO übernehmen kann.
Wäre nett, wenn mir jemand von euch hier behilflich sein könnte.
Danke im Voraus.
Zuletzt bearbeitet: