Suchergebnisse

Hi, i have set up inadyn-mt according to this http://freetz.org/wiki/packages/inadyn-mt.en and here is a result of work process: Jan 30 14:42:41 fritz user.notice INADYN[17154]: Wed Jan 30 14:42:41 2013: N:DYNDNS: My IP address: 87.xxx.xxx.xxx Jan 30 14:42:41 fritz user.warn INADYN[17154]...

Thanks for information. I think that i found the source of problem. I recompiled kernel module ftdi_sio.ko and now this driver is in version 1.5.0 So far so good. So likely driver in version 1.4.3 wasn't working properly. Regards

Hello, i'm trying to run card reader phoenix usb (3,57-6MHz ver.7.6) on my 7340. I use this reader on my 7240 without any problem. Below i include some logs from 7240 & 7340, maybe someone can tell me something based on these logs. Reader is attached with this command: modprobe ftdi_sio...

Hi, at the moment i have 7240 and i want to move to 7340 or 7360 or 7390. Is there any difference at working stability with freetz on board ? Or it doesn't matter from freetz point of view, which model i will buy ? I will be using Vsftpd, Osc... and optionally samba and transsmision...

Hi, i'm currently using 7240 and i started to think about 7340/7390. My main goal is to achieve better transfer rate from external disk drive. So, can anybody who has 7340 or 7390 tell me,what is your max transfer speed via ftp or samba (through cable) ,when downloading large file eg700MB...

samba or ftp transfer speed Hi, I have 7240 and i want to compare it with 7390 or 7340 which has faster cpu and 1G lan port. So i want to ask someone who has 7390 or 7340 about transfer rate. What is your max transfer speed via ftp or samba when downloading larg file e.g.700MB from hard...

these settings are for samba and i was using vsftp for test. But i have these setting under samba and under samba i have a little lower transfer. Did you removed orginal fritz stuff like samba,ftp during compilation of freetz ? And that is interesting that you have slower ftp than samba. I...

ok thanks guys, so i see that i have not optimal transfer speed and there is something to do better. I will start trying to figure out why my transfer isn't optimal. Regards, Tom

are you sure that kBit ? because 4500kBit = 562.5 kbytes which would be a very poor transfer.

thanks, this is really poor transfer rate... i shouldn't be mad for my own. I have 1800 kbytes/s(fritz-->computer) over 54 MBit WLAN. Same WLAN give me 2700 kbytes/s when transfering between 2 computers.

Hi, i have 7240, currently using freetz 6780 with vsftp. My average transfer rate from ext3 partition connected through usb hub to fritzbox is 3000kbytes/s Is this max what i can get ? I'll add that transfer between my 2 computers through samba in the same network connected with this...

The problem was in hardware, box was replaced by avm.

ANNEX=B CONFIG_DSL_MULTI_ANNEX=n CONFIG_ANNEX=B Regards Tom

because at "Box info" page i have: annex B under "Environment variables" and also, when i execute command env under telnet i see annex=B this is not enough to confirm annex type ? I cannot test it through dsl line ,because i dont have any at the moment. I will be in need of annex A in April or...

Hi, i have 7240 1&1 this is my config: 7240_7270_v2_labor_dsl_04.88freetz-devel-6483.de after uploading image i tried to change annex unsuccesfully. I tried in this way: echo "kernel_args annex=A" > /proc/sys/urlader/environment echo "annex A" > /proc/sys/urlader/environment export...

it looks like nothing changed to me. Both problems which i mentioned before are still there.

Hi, it works ,but not everything is translated. See picture. http://tinyurl.com/4t5vmyk And there is nothing displayed(no usb item showed) at usb devices page, despite that there is one item properly detected.

Hi, is there a way to force usb detection ? Normally usb detection is started when item is connected to usb. I have hdd enclosure which is detected by fritz 7240 when this item is plugged to box. But it is never detected if enclosure is already plugged and i will do box reboot. So that is why...

Hi, again can anybody tell me just this one thing, what will happen when you plug into fritz 7240 or 7270 only card reader(or usb to sata controler) without any memory (or hdd disc) inside. What is displayed at Heimnetz/USB-Gerate ,what speed is showed: 12MBit/s or 480 ? Take a look at picture...

Hi sorry for late answer. So at present i'm building firmware with such a configuration: Firmware language (de) Mod Language (en) When i tried once to build with (en) firmware language, it killed box, so i never again tried to build with (en) . Regards, Tom