7270 in Reboot Schleife

sebr

Mitglied
Mitglied seit
9 Apr 2010
Beiträge
219
Punkte für Reaktionen
1
Punkte
18
Hallo,

habe hier eine FB 7270_V2 die einfach nicht aus der Rebootschleife will. Habe bisher (mehrmals) ein Recovery gemach und auch mit dem rukerneltool geflasht. Mit der Anleitung hier im Forum gehalten und es lief auch ohne Probleme oder Fehlermeldung durch. Allerdings rebootet die Box weiterhin. Also hab ich mich an die Konsole gemacht und hier die Ausgabe beim booten:

Code:
(AVM) EVA Revision: 1.544 Version: 1544
(C) Copyright 2005 AVM Date: Oct 24 2008 Time: 11:07:57 (1) 2 0x0-0x41D

[FLASH:] SPANSION Uniform-MirrorBit-Flash 16MB 64 Bytes WriteBuffer
[FLASH:](Eraseregion [0] 128 sectors a 128kB)
[SYSTEM:] UR8 on 360MHz/120MHz syncron

Eva_AVM >AVM decompress Kernel:
..............................executeProgram on 0x94103DD0
Linux version 2.6.32.41 (gcc version 4.4.4 (Buildroot 2010.05) ) #1 Wed Oct 5 15
:02:54 CEST 2011
[set_wlan_dect_config] pConfig[0] 0x90000980
[set_wlan_dect_config] pConfig[1] 0x90000994
{clone_wlan_dect_config} config.Len 16
{clone_wlan_dect_config} config.Len 1026
[set_wlan_dect_config_address] new_pConfig=0x945bf260 0x945bf260
[set_wlan_dect_config_address] new_pConfig[0]=0x945bf274
[set_wlan_dect_config_address] new_pConfig[1]=0x945bf288
myenvp=945a5484
(945a5684)HWRevision : (945a568f)139.1.0.6
(945a5699)ProductID : (945a56a3)Fritz_Box_7270_16
(945a56b5)SerialNumber : (945a56c2)0000000000000000
(945a56d3)annex : (945a56d9)B
(945a56db)autoload : (945a56e4)yes
(945a56e8)bootloaderVersion : (945a56fa)1.544
(945a5700)bootserport : (945a570c)tty0
(945a5711)cpufrequency : (945a571e)360000000
(945a5728)firstfreeaddress : (945a5739)0x946BDA1C
(945a5744)firmware_version : (945a5755)avm
(945a5759)firmware_info : (945a5767)54.05.07
(945a5770)flashsize : (945a577a)0x01000000
(945a5785)jffs2_size : (945a5790)16
(945a5793)kernel_args : (945a579f)annex=B
(945a57a7)maca : (945a57ac)00:1F:3F:EF:0F:B6
(945a57be)macb : (945a57c3)00:1F:3F:EF:0F:B7
(945a57d5)macwlan : (945a57dd)00:1F:3F:D4:F6:34
(945a57ef)macdsl : (945a57f6)00:1F:3F:EF:0F:B8
(945a5808)memsize : (945a5810)0x04000000
(945a581b)modetty0 : (945a5824)38400,n,8,1,hw
(945a5833)modetty1 : (945a583c)38400,n,8,1,hw
(945a584b)mtd0 : (945a5850)0x90000000,0x90000000
(945a5866)mtd1 : (945a586b)0x90020000,0x90F80000
(945a5881)mtd2 : (945a5886)0x90000000,0x90020000
(945a589c)mtd3 : (945a58a1)0x90F80000,0x90FC0000
(945a58b7)mtd4 : (945a58bc)0x90FC0000,0x91000000
(945a58d2)my_ipaddress : (945a58df)192.168.178.1
(945a58ed)prompt : (945a58f4)Eva_AVM
(945a58fc)req_fullrate_freq : (945a590e)120000000
(945a5918)sysfrequency : (945a5925)120000000
(945a592f)urlader-version : (945a593f)1544
(945a5944)usb_board_mac : (945a5952)00:1F:3F:EF:0F:B9
(945a5964)usb_rndis_mac : (945a5972)00:1F:3F:EF:0F:BA
(945a5984)usb_device_id : (945a5992)0x5E00
(945a5999)usb_revision_id : (945a59a9)0x0200
(945a59b0)usb_manufacturer_name : (945a59c6)AVM
(945a59ca)wlan_key : (945a59d3)5359660820827813
argc=2 argv=945a5e84
[0]: gocommand
[1]: annex=B
[prom_init] fw_arg2 0x945a5484
[prom_init] dst_env 0x945a5484
[prom_init] fw_arg1 0x945a5e84
[prom_init] dst_cmdline945a5e84
[prom_init] 0x945a5684 [0]
[prom_init] 0x945a568f [1]
[prom_init] 0x945a5699 [2]
[prom_init] switch to ram location
[prom_init] envp[0]= "HWRevision"="139.1.0.6"
[prom_init] envp[2]= "ProductID"="Fritz_Box_7270_16"
[prom_init] envp[4]= "SerialNumber"="0000000000000000"
[prom_init] envp[6]= "annex"="B"
[prom_init] envp[8]= "autoload"="yes"
[prom_init] envp[10]= "bootloaderVersion"="1.544"
[prom_init] envp[12]= "bootserport"="tty0"
[prom_init] envp[14]= "cpufrequency"="360000000"
[prom_init] envp[16]= "firstfreeaddress"="0x946BDA1C"
[prom_init] envp[18]= "firmware_version"="avm"
[prom_init] envp[20]= "firmware_info"="54.05.07"
[prom_init] envp[22]= "flashsize"="0x01000000"
[prom_init] envp[24]= "jffs2_size"="16"
[prom_init] envp[26]= "kernel_args"="annex=B"
[prom_init] envp[28]= "maca"="00:1F:3F:EF:0F:B6"
[prom_init] envp[30]= "macb"="00:1F:3F:EF:0F:B7"
[prom_init] envp[32]= "macwlan"="00:1F:3F:D4:F6:34"
[prom_init] envp[34]= "macdsl"="00:1F:3F:EF:0F:B8"
[prom_init] envp[36]= "memsize"="0x04000000"
[prom_init] envp[38]= "modetty0"="38400,n,8,1,hw"
[prom_init] envp[40]= "modetty1"="38400,n,8,1,hw"
[prom_init] envp[42]= "mtd0"="0x90000000,0x90000000"
[prom_init] envp[44]= "mtd1"="0x90020000,0x90F80000"
[prom_init] envp[46]= "mtd2"="0x90000000,0x90020000"
[prom_init] envp[48]= "mtd3"="0x90F80000,0x90FC0000"
[prom_init] envp[50]= "mtd4"="0x90FC0000,0x91000000"
[prom_init] envp[52]= "my_ipaddress"="192.168.178.1"
[prom_init] envp[54]= "prompt"="Eva_AVM"
[prom_init] envp[56]= "req_fullrate_freq"="120000000"
[prom_init] envp[58]= "sysfrequency"="120000000"
[prom_init] envp[60]= "urlader-version"="1544"
[prom_init] envp[62]= "usb_board_mac"="00:1F:3F:EF:0F:B9"
[prom_init] envp[64]= "usb_rndis_mac"="00:1F:3F:EF:0F:BA"
[prom_init] envp[66]= "usb_device_id"="0x5E00"
[prom_init] envp[68]= "usb_revision_id"="0x0200"
[prom_init] envp[70]= "usb_manufacturer_name"="AVM"
[prom_init] envp[72]= "wlan_key"="5359660820827813"
bootconsole [early0] enabled
CPU revision is: 00019068 (MIPS 4KEc)
[memsize] memsize=0x4000000
[memsize] memsize=0x4000000
ur8_clk_get_pll_factor: 300000000
ur8_get_pci_clock 33333333
[setup_pci_master]
[wait_pciif_ready] UR8_PCI_MASTER_ABORT! 00000000. retry=0
 PCI Interface Not Ready (i=16000), state = 0x262148
PCI core not ready, resetting again ...
ur8_clk_get_pll_factor: 300000000
ur8_get_pci_clock 33333333
[setup_pci_master]
registering PCI controller with io_map_base unset
TI UR8 (7270), ID: 0x0030, Revision: 0x10
Determined physical RAM map:
Wasting 8192 bytes for tracking 256 unused pages
Zone PFN ranges:
  Normal   0x00014000 -> 0x00018000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00014000 -> 0x00018000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: annex=B
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[avm_cache_set_coherency]: setting cache coherency for HWRevision=139 to write t
hrough
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes
Memory: 57880k/63872k available (3260k kernel code, 5924k reserved, 1467k data,
132k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:256
[mips_cpu_irq_init] irq_base 0
[mips_cpu_irq_init]change irqline 21 -> irqchan(prio) 8
[mips_cpu_irq_init]change irqline 8 -> irqchan(prio) 21
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Calibrating delay loop... 359.62 BogoMIPS (lpj=1798144)
Mount-cache hash table entries: 512
kernel_init: started
kernel_init: kernel locked
NET: Registered protocol family 16
[cpmac] Version: 1.108.1.87 - Revision 811:1514 - Mi  5.10.2011 15:02:33
MUSB UR8 pdev active!
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pcibios_read_config: accessing present PCI slot : 14, where 0, size 4
Master and Slave Enabled
NET: Registered protocol family 8
NET: Registered protocol family 20
musb_hdrc: version 6.0, cppi-dma, host, debug=0
musb_core_init 1505: musb_hdrc: hw_ep 0shared, max 64
musb_core_init 1505: musb_hdrc: hw_ep 1tx, max 512
musb_core_init 1513: musb_hdrc: hw_ep 1rx, max 512
musb_core_init 1505: musb_hdrc: hw_ep 2tx, max 512
musb_core_init 1513: musb_hdrc: hw_ep 2rx, max 512
musb_core_init 1505: musb_hdrc: hw_ep 3tx, max 512
musb_core_init 1513: musb_hdrc: hw_ep 3rx, max 512
musb_core_init 1513: musb_hdrc: hw_ep 4rx, max 512
musb_hdrc: USB Host mode controller at a3400000 using DMA, IRQ 39
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
[loadcontrol]module musb_hdrc registered
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.32.41 musb-hcd
usb usb1: SerialNumber: musb_hdrc
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
avm_net_trace: New net trace device 'usb1' registered with minor 161.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
[simple_profiling] 0 entries 50 min
squashfs: version 3.4 (2008/08/26) Phillip Lougher
Installing knfsd (copyright (C) 1996 [email protected]).
fuse init (API version 7.13)
msgmni has been set to 113
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
[avm_membench_init]
avm_net_trace: Up and running.
[loadcontrol] set auto - scale=1
[avm] configured: watchdog event debug enable direct gpio

AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0, build: Oct  5 2011
15:02:01)
[simple-profiling]: no performance counters implemented
[simple-profiling]: no performance counters implemented
[avm]: AVM Simple Profiling enabled.
Serial: SERIAL_AVM_8250 driver
ttyS0 at MMIO 0x0 (irq = 15) is a PORT_16550A
[physmap_flash_probe] line=101, doing probes
physmap platform flash device: 01000001 at 10000000
[do_map_probe] driver_name=cfi_probe
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
6 find_squashfs partitions found on MTD device physmap-flash.0
Creating 6 MTD partitions on "physmap-flash.0":
0x0000001c5300-0x000000f80000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be s
maller than an erase block -- forcing read-only
0x000000020000-0x0000001c5300 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be s
maller than an erase block -- forcing read-only
0x000000000000-0x000000020000 : "urlader"
0x000000f80000-0x000000fc0000 : "tffs (1)"
0x000000fc0000-0x000001000000 : "tffs (2)"
0x000000e80000-0x000000f80000 : "jffs2"
Generic platform RAM MTD, (c) 2004 Simtec Electronics
[dectsync] inactive
prefetch_code: 942bb800: len=2656
[cpmac] [cpmac_if_register] dev cpmac0 (phy_id 0) registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
CAPI Subsystem Rev 1.1.2.8
[loadcontrol]module avm_pa registered
TCP cubic registered
mcfw: IGMPv3 fast forwarding
NET: Registered protocol family 10
NET: Registered protocol family 17
NET: Registered protocol family 8
atmpvc_init() failed with -17
TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0)
      mount on mtd3 and mtd4 (double buffering)
Adam2 environment variables API installed.
kernel_init: basic setup done
[squashfs] use lzma compression
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing bootloader memory: 1024k freed
Freeing unused kernel memory: 132k freed
trying /sbin/init
starting pid 24, tty '/dev/ttyS0': '/etc/init.d/rc.S'
tar: removing leading '/' from member names
source files in group 0 ...
/etc/init.d/S00-signal    /etc/init.d/S05-watchdog  /etc/init.d/S09-rtc
/etc/init.d/S01-head      /etc/init.d/S08-tffs
/etc/init.d/S02-led       /etc/init.d/S09-config
executing /etc/init.d/S00-signal
executing /etc/init.d/S01-head
TFFS Name Table H
executing /etc/init.d/S02-led
led_modul_Fritz_Box_7270_16: module license '
(C) Copyright 2008 by AVM
' taints kernel.
Disabling lock debugging due to kernel taint
__io_remap_setwriteprotect: error: no pte for addr 97ae0000
[led_gpio_bit_driver_init] gpio 1 name power
[led_gpio_bit_driver_init] gpio 9 name internet
[led_gpio_bit_driver_init] gpio 27 name festnetz
[led_gpio_bit_driver_init] gpio 28 name wlan
[led_gpio_bit_driver_init] gpio 17 name dual1
[led_gpio_bit_driver_init] gpio 35 name dual2
[button_init] name button_wlan gpio 25 active low
[button_init] name button_dect gpio 23 active low
[button_init] name button_both gpio 0 active high
executing /etc/init.d/S05-watchdog
AVM_WATCHDOG: System Init UEberwachung 480 Sekunden
executing /etc/init.d/S08-tffs
mknod: /var/flash/ar7.cfg: File exists
checkempty: : No such file or directory
overwrite annex
P-Defaults: not configured - skip.
executing /etc/init.d/S09-config
overwrite annex
executing /etc/init.d/S09-rtc
__io_remap_setwriteprotect: error: no pte for addr 97ac4000
rtc-avm rtc-avm.0: rtc core: registered avm as rtc0
[avm-rtc]: avm_rtc_probe: register: ret=0x97968200
[avm-rtc]: avm_rtc_probe: success
exceute files in group 0 ...
/etc/init.d/E05-basemodules
group 0 done ...
source files in group 1 ...
/etc/init.d/S10-html        /etc/init.d/S12-default
/etc/init.d/S10-vm          /etc/init.d/S15-filesys
/etc/init.d/S11-config_def  /etc/init.d/S17-capi
/etc/init.d/S11-piglet      /etc/init.d/S17-tam
executing /etc/init.d/S10-html
executing /etc/init.d/S10-vm
executing /etc/init.d/S11-config_def
executing /etc/i
[avm_debug]redirect kernel-messages (/dev/debug)
nit.d/S11-piglet
__io_remap_setwriteprotect: error: no pte for addr 97B00000
[piglet]use settings for 139(6 gpios from hw_config)

[get_wlan_dect_config] buffer 0x97B09E10 len 132
[get_wlan_dect_config] wlan_dect_config[0] 0x945BF274
DECT
0x2 0x1 0x10 0x0 0x1 0x5 0x1 0x2A 0x63 0xB9 0xF8 0x2 0x1 0x77 0x3 0x1 0x6 0x4 0x
1 0x8
patch_dectfw: patch_adress: 7A6E max_len: 22 with Version 2 Len: 16
patch_dectfw: C0A0B000, datalen = 34415,

*******************************************[4294938364]system-load 6  23 tasks:5
4 % curr:modprobe(30 %) max:modprobe(30 %, pid:203), readytorun: 4, pgfault 2231
/s (max 1 avg 1.0)
************************
dect_file_process: upload of '/lib/modules/dectfw_secondlevel.hex' successfull
[piglet]bitfile '/lib/modules/microvoip_isdn_top.bit'

[piglet] clock from pll3(384000000)
[piglet] bitfile 169291 bytes done
[piglet]TDM: FS: 8000 Hz CLK:2047790 Hz
executing /etc/init.d/S12-default
checkempty: : No such file or directory
executing /etc/init.d/S15-filesys
__io_remap_setwriteprotect: error: no pte for addr 97B40000
JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
[jffs2] Mount /data success (mtd5 size 1048576)
[jffs2] write env variable jffs2_size to 16
__io_remap_setwriteprotect: error: no pte for addr 97BA8000
loop: module loaded
[ramdisk] loop is loaded
[ramdisk] ext2 is loaded
[ramdisk] WARNING: Internal Memory Mountpoint '/var/media/ftp' already occupied
- Listing content before deletion:
/var/media/ftp:
[ramdisk] WARNING: Internal Memory Mountpoint '/var/media/ftp' already occupied
- deleting...
next free loop devive: /dev/loop0
[ramdisk] Internal Memory: loopdevice @ 0
[ramdisk] Internal Memory: mountpoint @ /var/media/ftp
[ramdisk] Internal Memory assigned @ /var/media/ftp
executing /etc/init.d/S17-capi
mknod: /dev/capi20: File exists
__io_remap_setwriteprotect: error: no pte for addr 94880000
[pcmlink]svn: 1454
__io_remap_setwriteprotect: error: no pte for addr 94A00000
[4294939041][isdn]svn:2859
driver params overwritten io_addr=0x0 irq_num=0
[pcmlink]chrony-support

[pcmlink]c55: simple checksum: 18EFE8C
[C55LOAD] ERROR:magic =12051978 is not set to 1234 from c55
[4294939165]PCMLINK: Version 5.430 Codecslots=13 Slics=2 Pots=1 TE=2 NT=2 DECT=4
  DSP-EC: 4
hardware-error: find only 1 slics - try it again
hardware-error: find only 1 slics - try it again
Call Trace:
[<94113754>] dump_stack+0x8/0x34
[<941228e4>] panic+0x34/0x1ec
[<94a4c2a0>] Reset_FPGA+0xb4/0x110 [isdn_fbox_fon5]
[<94a4c3e0>] Init_FPGA+0xe4/0x10c [isdn_fbox_fon5]
[<94a45078>] InitAnalog+0x80/0x2bc [isdn_fbox_fon5]
[<94a0ef24>] CM_Activate+0xa4/0xd8 [isdn_fbox_fon5]
[<94333818>] avm_stack_attach+0x224/0x278
[<94980144>] init_module+0x144/0x15c [isdn_fbox_fon5]
[<941076cc>] do_one_initcall+0x6c/0x1fc
[<9414e85c>] sys_init_module+0xdc/0x22c
[<941026e4>] stack_done+0x20/0x3c

Kernel panic - not syncing: hardware-error: find only 1 slics - bye bye

WARNING: use tffs in panic mode (minor 96)
Rebooting in 3 seconds..[4294939428]system-load 7  29 tasks:41 % curr:modprobe(3
9 %) max:modprobe(39 %, pid:250), readytorun: 5, pgfault 638/s (max 1 avg 1.0)
[ur8_machine_restart] reset all 0x80000043 at address a8611600
[ur8_machine_restart] rebootý
"printenv" liefert:
Code:
HWRevision            139.1.0.6
ProductID             Fritz_Box_7270_16
SerialNumber          0000000000000000
annex                 B
autoload              yes
bootloaderVersion     1.544
bootserport           tty0
cpufrequency          360000000
firstfreeaddress      0x946BDA1C
firmware_version      avm
firmware_info         54.05.07
flashsize             0x01000000
jffs2_size            16
kernel_args           annex=B
maca                  00:1F:3F:EF:0F:B6
macb                  00:1F:3F:EF:0F:B7
macwlan               00:1F:3F:D4:F6:34
macdsl                00:1F:3F:EF:0F:B8
memsize               0x04000000
modetty0              38400,n,8,1,hw
modetty1              38400,n,8,1,hw
mtd0                  0x90000000,0x90000000
mtd1                  0x90020000,0x90F80000
mtd2                  0x90000000,0x90020000
mtd3                  0x90F80000,0x90FC0000
mtd4                  0x90FC0000,0x91000000
my_ipaddress          192.168.178.1
prompt                Eva_AVM
req_fullrate_freq     120000000
sysfrequency          120000000
urlader-version       1544
usb_board_mac         00:1F:3F:EF:0F:B9
usb_rndis_mac         00:1F:3F:EF:0F:BA
usb_device_id         0x5E00
usb_revision_id       0x0200
usb_manufacturer_name  AVM
wlan_key              5359660820827813
Hoffe jemand kann helfen, bin am verzweifeln was da los ist :(

Danach wieder reboot.
 

Bibie

Aktives Mitglied
Mitglied seit
4 Jul 2008
Beiträge
2,872
Punkte für Reaktionen
4
Punkte
0
Hallo sebr,

ich hab hier auch eine FB 7270v2 mit der BootloaderVersion 1.544 und sie fand sich ebenfalls in einer Rebootschleife wieder, nachdem ich sie von der 54.04.88 auf die 54.05.05 geflasht hatte. Es half auch nicht das 54.05.05er Recover, immer wieder diese Rebootschleife. Dann hatte ich das Recover der Version 54.04.86 genommen und siehe da, das Recover lief artig durch und die Box funktionierte wieder wie immer. :)

Anschließend hab ich die Box mit dem RuKernelTool von Rainer (nochmals danke für das sehr hilfreiche Tool) mit der neuen Firmware 54.05.05 geflasht - und diesmal ging alles bestens. Keine Rebootschleife mehr! :)

Vielleicht hilft es Dir ja auch, die Box nochmals mit der 54.04.86 zu recovern und dann mit dem RuKernelTool die neue Version 54.05.05 einzuspielen.

Ich versuche gerade die Labor-FW 54.05.07-20781 einzuspielen, mal sehen, ob sie das mitmacht...

Edit:

Update hat einwandfrei geklappt. Hab sie ganz normal per Firmware-Datei geflasht. Also meine Box macht wieder, was sie soll... :D
 
Zuletzt bearbeitet:
3CX

Statistik des Forums

Themen
235,892
Beiträge
2,067,347
Mitglieder
356,881
Neuestes Mitglied
LTH-doc