=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.08.23 22:39:31 =~=~=~=~=~=~=~=~=~=~=~=
#
(AVM) EVA Revision: 1.458 Version: 1458
(C) Copyright 2005 AVM Date: Apr 11 2008 Time: 10:36:56 (0) 2 0x0-0x41D
[FLASH:] SPANSION Uniform-MirrorBit-Flash 16MB 64 Bytes WriteBuffer
[FLASH:](Eraseregion [0] 128 sectors a 128kB)
[SYSTEM:] UR8 on 360MHz/120MHz syncron
Eva_AVM >
erase mtd1 ...........................................................................................................................
Eva_AVM >
flash ........................................................................................
erase mtd3 ..
Eva_AVM >
flash
erase mtd4 ..
Eva_AVM >
flash <Reboot Device>
<create new TFFS>
(AVM) EVA Revision: 1.458 Version: 1458
(C) Copyright 2005 AVM Date: Apr 11 2008 Time: 10:36:56 (1) 2 0x0-0x41D
[FLASH:] SPANSION Uniform-MirrorBit-Flash 16MB 64 Bytes WriteBuffer
[FLASH:](Eraseregion [0] 128 sectors a 128kB)
[SYSTEM:] UR8 on 360MHz/120MHz syncron
Eva_AVM ><Reboot Device>
(AVM) EVA Revision: 1.458 Version: 1458
(C) Copyright 2005 AVM Date: Apr 11 2008 Time: 10:36:56 (1) 2 0x0-0x41D
[FLASH:] SPANSION Uniform-MirrorBit-Flash 16MB 64 Bytes WriteBuffer
[FLASH:](Eraseregion [0] 128 sectors a 128kB)
[SYSTEM:] UR8 on 360MHz/120MHz syncron
Eva_AVM >AVM decompress Kernel:
.................executeProgram on 0x94237000
[prom_init] 0
[prom_init] argv[0]=gocommand
[prom_init] argv[1]=annex=B
[prom_init] fw_arg3 0x94643b70
LINUX started...
flashsize=16 MByte
&_end=0x942ac00c PFN_ALIGN(&_end)=0x942ad000 CPHYSADDR(PFN_ALIGN(&_end))=0x142ad000 memsize=0x4000000
[c55/wlan] membase = 0x14000000 memtop = 0x18000000 memsize = 0x4000000
[c55/wlan] memsegment0(size) = 3f60000 wlan(size) = 0x60000 c55(size) = 0x40000 memsegment2(size) = 0x0
[c55/wlan] mdesc[0]: base = 0x14000000 size = 0x3f60000
[c55/wlan] mdesc[1]: base = 0x17f60000 size = 0xa0000
[c55/wlan] mdesc[2]: base = 0x18000000 size = 0x0
[c55/wlan] mdesc[3]: base = 0x0 size = 0x0
Config serial console: console=ttyS0,38400n8r
[ur8_pre_init] System Clk = 60000000 Hz
(ur8_gpio_init)
ur8_clk_get_pll_factor: 300000000
ur8_get_pci_clock 33333333
(mips_reboot_setup)
plat_timer_setup TIMER IRQ: 7
Linux version 2.6.19.2 (3860) (gcc version 3.4.6) #1 Mon Nov 29 14:50:31 CET 2010
cpu-probe: Manufacturer MIPS
mips-config1: JTAG pressent
mips-config1: TLB size 16
mips-config3: Vectored interrupts implmented
CPU revision is: 00019068
[mips_clock] default 360000000 MHz
[ur8_clk_set_emif] SDRAM Refresh 0x3a8 Timing 0x2214717 Bank 0x21 Async 0xc42c301
[ur8_pci_init]
[pci] default: 33 MHz
[setup_pci_master]
[setup_pci_slave]
Exposing 67108864 memory over PCI
Setup Complete, Enabling PCI Interface
PCI Interface Running
PCI controller initialized
[ur8_vbus_set_prio] instance vbus_nwss_dma level 2 escalator disabled (count 255, floor 7)
[ur8_vbus_set_prio] instance vbus_sar_pdsp level 2 escalator disabled (count 255, floor 7)
[ur8_vbus_set_prio] instance vbus_buffer_manager level 2 escalator disabled (count 255, floor 7)
[ur8_vbus_set_prio] instance vbus_usb level 5 escalator disabled (count 255, floor 7)
[ur8_vbus_set_prio] instance vbus_vlynq level 7 escalator disabled (count 255, floor 7)
[ur8_vbus_set_prio] instance vbus_pci level 5 escalator disabled (count 255, floor 7)
[ur8_vbus_set_prio] instance vbus_c55 level 3 escalator disabled (count 255, floor 7)
[ur8_vbus_set_prio] instance vbus_tdm level 0 escalator disabled (count 255, floor 7)
[ur8_vbus_set_prio] instance vbus_mips level 3 escalator disabled (count 255, floor 7)
Determined physical RAM map:
memory: 03f60000 @ 14000000 (usable)
memory: 000a0000 @ 17f60000 (reserved)
[init_bootmem]
[free_bootmem]
[reserve_bootmem]
[mem_map-hack]: reduce size from 3145728 524288 Bytes
[mem_map-hack]: move map base from 0x942b0000 to 0x94030000
[request_resource] Kernel code: start 0x14000000 < root->start 0x17f60000
[request_resource] Kernel data: start 0x141c20b0 < root->start 0x17f60000
Built 1 zonelists. Total pages: 97378
Kernel command line: annex=B console=ttyS0,38400n8r
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 2048 (order: 11, 8192 bytes)
CPU frequency 360.00 MHz
Using 180.000 MHz high precision timer.
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[free_all_bootmem]
Memory: 61184k/64896k available (1800k kernel code, 3656k reserved, 464k data, 132k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
[ur8_mtd_init]
[ur8_mtd_init] flashsize = 0x01000000 Byte 16 MBytes
[ur8_mtd_init] mtd[0] = 0x90000000,0x90000000
[ur8_mtd_init] mtd[1] = 0x90020000,0x90F80000
[ur8_mtd_init] mtd[2] = 0x90000000,0x90020000
[ur8_mtd_init] mtd[3] = 0x90F80000,0x90FC0000
[ur8_mtd_init] mtd[4] = 0x90FC0000,0x91000000
[ur8_mtd_init] mtd[5] = 0x90000000,0x90000000
pcibios_read_config: accessing present PCI slot : 14, where 0, size 4
Master and Slave Enabled
pktsched: using high resolution timer
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
squashfs: version 3.2 (2007/01/02) Phillip Lougher
fuse init (API version 7.8)
io scheduler noop registered (default)
avm_net_trace: Up and running.
[avm] configured: watchdog event debug enable direct gpio
AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0, build: Nov 29 2010 14:48:08)
Serial: 8250/16550 driver $Revision: 1.3 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 15) is a UR8_UART
[cpmac] Version: 1.130 - Revision 790:1177 - Mo 29.11.2010 14:49:19
[dectsync] inactive
[cpmac] [cpmac_if_register] dev cpmac0 (phy_id 0) registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
physmap platform flash device: 01000001 at 10000000
physmap-flash.1: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.1: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
[ur8_jffs2_parser_function] mtd_info->name physmap-flash.1 mtd_info->index 0 param=0 p_mtd_pat=0x97e009bc
[ur8_jffs2_parser_function] try partition kernel (offset 0x20000 len 16121856)
[ur8_squashfs_parser_function] mtd_info->name physmap-flash.1 mtd_info->index 0 param=0 p_mtd_pat=0x97e009bc
[ur8_squashfs_parser_function] *p_mtd_pat->name filesystem
[ur8_squashfs_parser_function] try partition kernel (offset 0x20000 len 16121856 blocksize=20000)
[ur8_squashfs_parser_function] magic found @pos 0xe1f00
[ur8_squashfs_parser_function] flashsize=1000000
[ur8_squashfs_parser_function] jffs2_start@c60000 size: 50
6 find_squashfs partitions found on MTD device physmap-flash.1
Creating 6 MTD partitions on "physmap-flash.1":
0x000e1f00-0x00f80000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
[ur8_mtd_add_notifier] name rootfs
[ur8_mtd_add_notifier] use rootfs
[ur8_mtd_add_notifier] root device: /dev/mtdblock0 (rootfs)
0x00020000-0x000e1f00 : "kernel"
mtd: partition "kernel" doesn't end on an erase block -- force read-only
[ur8_mtd_add_notifier] name kernel
[ur8_mtd_add_notifier] skip kernel
0x00000000-0x00020000 : "urlader"
[ur8_mtd_add_notifier] name urlader
[ur8_mtd_add_notifier] skip urlader
0x00f80000-0x00fc0000 : "tffs (1)"
[ur8_mtd_add_notifier] name tffs (1)
[ur8_mtd_add_notifier] skip tffs (1)
0x00fc0000-0x01000000 : "tffs (2)"
[ur8_mtd_add_notifier] name tffs (2)
[ur8_mtd_add_notifier] skip tffs (2)
0x00c60000-0x00f80000 : "jffs2"
[ur8_mtd_add_notifier] name jffs2
[ur8_mtd_add_notifier] skip jffs2
Generic platform RAM MTD, (c) 2004 Simtec Electronics
mtd-ram mtd-ram.2: no memory resource specified
[ur8_ram_mtd_set_rw] PLATRAM_RO
mtd-ram: probe of mtd-ram.2 failed with error -2
CAPI Subsystem Rev 1.1.2.8
TCP cubic registered
mcfw: IGMPv3 fast forwarding
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
MUSB UR8 pdev active!
PCI_STATUS_SET: 40000
PCI_STATUS_CLR: 40000
PCI_HOST_INT_EN: 0
PCI_HOST_INT_CLR: 0
PCI_BE_INT_En: 0
PCI_BE_INT_CLR: 0
[pci_int_init] done
[TFFS_Init] 1: mtd_number: 3 | mtd_number2: 4
Time: MIPS clocksource has been installed.
[get_mtd_device_wrapped] 1: 3
[get_mtd_device_wrapped] 2
[TFFS_Init] 3
[TFFS_Init] 4.0
[put_mtd_device_wrapped] 1
[put_mtd_device_wrapped] 2
[put_mtd_device_wrapped] 3
[get_mtd_device_wrapped] 1: 4
[get_mtd_device_wrapped] 2
[TFFS_Init] 5
[TFFS_Init] 6
[TFFS_Init] 7
[TFFS_Init] 8
[TFFS_Init] 9
TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0)
mount on mtd3 and mtd4 (double buffering)
Adam2 environment variables API installed.
[avm_new] push_button_gpio=25 value=1 enabled
VFS: Mounted root (squashfs filesystem) readonly.
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 132k freed
[4294939091]maxrun: 1
3
init started: BusyBox v1.8.2 (2010-11-29 14:52:58 CET)
starting pid 106, tty '': '/etc/init.d/rc.S'
WARNING: TFFS Name Table update ! (current @B new @G)
AVM_WATCHDOG: System Init UEberwachung 240 Sekunden
mknod: /var/flash/ar7.cfg: File exists
overwrite annex
starting AVM_LED_EVENTS
led_modul_Fritz_Box_DECT_W920V: module license '
(C) Copyright 2008 by AVM
' taintskernel.
[led_gpio_bit_driver_init] gpio 1 name power
[led_gpio_bit_driver_init] gpio 36 name update
[led_gpio_bit_driver_init] gpio 32 name dsl
[led_gpio_bit_driver_init] gpio 17 name pppoe
[led_gpio_bit_driver_init] gpio 9 name voip_con
[led_gpio_bit_driver_init] gpio 27 name festnetz
[led_gpio_bit_driver_init] gpio 21 name dual1
[led_gpio_bit_driver_init] gpio 22 name dual2
[led_gpio_bit_driver_init] gpio 28 name wlan
[BUTTON] no buttons defined - disable new button controls
[LED] "wyatt_earp_turn_off_leds" (0x00000000) not loaded
mknod: /dev/led: File exists
checkempty: : No such file or directory
cat /etc/default.049/telefon_misc.default > /var/flash/telefon_misc
checkempty: : No such file or directory
cat /etc/default.049/fx_lcr.default > /var/flash/fx_lcr
checkempty: : No such file or directory
cat /etc/default.049/fx_conf.default > /var/flash/fx_conf
checkempty: : No such file or directory
cat /etc/default.049/fx_moh.default > /var/flash/fx_moh
checkempty: : No such file or directory
DECT Defaults: cat /etc/default.Fritz_Box_7270/avm/dect_eeprom > /var/flash/dect_eeprom
checkempty: : No such file or directory
[piglet]use default-gpio-settings
[avm_new]push_button_ctrl: gpio=30 value=0 enabled
[avm_new]push_button_ctrl:'Werkseinstellungs-Taster': enable=2 gpio=30 regaddr=00000000 button_type=1
[avm_new]push_button_ctrl: gpio=23 value=0 enabled
[avm_new]push_button_ctrl:'Taster_4': enable=2 gpio=23 regaddr=00000000 button_type=0
patch_dectfw: patch_adress: 7ad2 max_len: 22 with Version 2 Len: 16
patch_dectfw: c006c000, datalen = 34584,
**********************************<6>[avm_new]push_button 'Wlan-Taster', released: GPIO=25 presses=6250 key=button_key_3
*********************************
dect_file_process: upload of '/lib/modules/dectfw_secondlevel.hex' successfull
[piglet]bitfile '/lib/modules/microvoip_isdn_top.bit'
[4294940158]maxrun: 2
[piglet] Read 169297 bytes total from file
[piglet]TDM: FS: 8000 Hz CLK:2047800 Hz
[jffs2] xx=mtd5: 00320000 00020000 "jffs2"
[jffs2] i=mtd5:
[jffs2] jffs2_pat=5
[jffs2] i=00320000
[jffs2] jffs2_size=50
[jffs2] i=00020000
[jffs2] i="jffs2"
[jffs2] load jffs2 module
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
[jffs2] mount jffs
[jffs2] write env variable jffs2_size to 50
/sbin/start_plugin.sh[263]: Plugins awaited: mini onlinepb ntfs samba
loop: loaded (max 8 devices)
TAM: create JFFS2 directory /data/tam
TAM Defaults: cp /etc/default.Fritz_Box_7270/avm/config.tam /data/tam/config
[avm_debug]redirect kernel-messages (/dev/debug)
VINAX Driver, Version 0.1.5.99
(c) Copyright 2005, Infineon Technologies AG
<VINAX COMPATIBILITY CHECK> interface version is 1
VINAX_DRV: VINAX_InitModuleRegCharDev: Registering device vinax, vinax (PROC_FS)T >> init dev: base address = 0x1C000000
T >> parse: opt value = 9
T >> open device: /dev/vinax/0.
T >> ioct(FIO_VINAX_DEV_INIT): baseaddr = 0x1C000000, IRQ = 9
usedIrq: 9
VINAX: GOT INTERRUPT: startup
locking interrupts
+++++++++++++++++++++++++++++++++++++++init ATM OAM!!T >> Line = 00 Return = 0
T >> open device: /dev/vinax/0.
T >> Start Download </lib/modules/vinax_fw_adsl.bin>, size: 540916
device already started--> execute FW Download
VINAX_DRV[00]: Start Download - DMA transfere
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[53] found - skipped
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[54] found - skipped
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[55] found - skipped
VINAX_DRV[00]: BM-7 CS: EMPTY <code> page[61] found - skipped
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[62] found - skipped
checked download state machine (= 4)
VINAX_DRV[00]: DL/CS - Wait for 1. Response
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[40] found - skipped
T >> Line = 00 Return = 0
state has changed
VINAX_DRV[00]: DL/CS 1. response received - done
==================
Configuring Vinax
==================
DSL Mode=VB
Profile=17A
Trellis=on
VDSL: US_max_datenrate = 150000000
VDSL: DS_max_datenrate = 150000000
ADSL: US_max_datenrate = 32768000
ADSL: DS_max_datenrate = 32768000
DSL: start DSL daemon (pid 307).
DSL: using firmware file - /lib/modules/vinax_fw_adsl.bin
DSL: using dynamic FW script - /nv/get_fw.sh
DSL: DSL daemon running in background now! (pid=309)
DSL: Device granularity is 1
DSL: No firmware pointer
DSL: No 2nd firmware pointer
DSL: Given warmstart memory will be analyzed...
DSL: using external memory
DSL: No mapping information (line -> device channel) provided. Taking internal default settings.
DSL[00]: VINAX driver : 0.1.5.99
unlocking interrupts
VINAX: GOT INTERRUPT: user reset
locking interruptsDSL[00]: VINAXX[0] reset done - mask [0]0x00000001 [1]0x00000000 [2]0x00000000 [3]0x00000000
device already started--> execute FW Download
VINAX_DRV[00]: Start Download - DMA transfere
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[53] found - skipped
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[54] found - skipped
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[55] found - skipped
VINAX_DRV[00]: BM-7 CS: EMPTY <code> page[61] found - skipped
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[62] found - skipped
checked download state machine (= 4)
VINAX_DRV[00]: DL/CS - Wait for 1. Response
polling for dsl_daemon (attempt 1).
dsl_daemon not ready yet. Try again in 2 seconds
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[40] found - skipped
state has changed
VINAX_DRV[00]: DL/CS 1. response received - done
DSL:
DSL: *****************************************************
DSL: DSL library version: 2.1.2
DSL: *****************************************************
DSL: Number of devices : 1
DSL: Number of lines : 1
DSL: Number of lines/device : 1
DSL: Number of channels/line : 1
DSL:
DSL: Memory usage of warm start resistent data base
DSL: magic key data base : 4 bytes
DSL: instance config data base : 28 bytes
DSL: device config data base : 4 bytes
DSL: global array config data base: 0 bytes
DSL: line config data base : 276 bytes
DSL: channel config data base : 136 bytes
DSL: line array config data base : 1216 bytes
DSL: --------------
DSL: Total : 1664 bytes
DSL:
DSL: Memory usage of status data base
DSL: device status data base : 8 bytes
DSL: line status data base : 356 bytes
DSL: channel status data base : 312 bytes
DSL: --------------
DSL: Total : 676 bytes
DSL:
DSL: Context memory usage
DSL: context structure : 1904 bytes
DSL: Timeout event lists : 96 bytes
DSL: --------------
DSL: Total : 2000 bytes
DSL: *****************************************************
DSL:
DSL: DSL_Init finished with device mask 0x00000001
DSL: Thread ID for thread VinaxCtrl is 1026 (PID 316)
DSL: Thread ID for thread tPM_Tick is 2051 (PID 317)
DSL: Thread ID for thread DmsAlive is 3076 (PID 318)
DSL: Thread ID for thread tAgentX is 4101 (PID 319)
DSL: Thread tAgentX, ID 4101 (PID 319) exited
DSL: Thread ID for thread tPipe_0 is 5126 (PID 320)
DSL: Thread ID for thread tPipe_1 is 6151 (PID 321)
DSL: Thread ID for thread tPipe_2 is 7176 (PID 322)
DSL[00]: Device Start EVT - UsrRst, DrvState 1 --> 1
DSL[00]: Line in reset - block!
polling for dsl_daemon (attempt 2).
Wait for dsl_daemon: success after 2 attempts. Keep booting now.
[dsl_pipe] dsl serial number successfully set to "465249545a21426f78466f6e574c414e37323730303031463346423743333131"
nReturn=0
nReturn=0 nLine=0
nReturn=0 nLine=0 nChannel=0 nDirection=0
nReturn=0 nLine=0 nChannel=0 nDirection=1
nReturn=0 nLine=0 nChannel=0
nReturn=0 nLine=0 nChannel=0
nReturn=0 nLine=0
enabling ADSL AnnexB and VDSL2
nReturn=0 nLine=0
nReturn=0 nLine=0
automode enabled
nReturn=0 nLine=0 nDirection=0
nReturn=0 nLine=0 nDirection=1
nReturn=0 nLine=0 nDirection=0
nReturn=0 nLine=0 nDirection=1
Setting inventory DSL-FW version number to 9.5.2.1.1.6
nReturn=1002 nLine=0
nReturn=0 nData="0049 0000 0001 "
nReturn=0 nData="0149 0000 0001 "
nReturn=0 nData="0249 0000 0001 "
nReturn=0 nData="2051 0000 0002 00000000 "
++++++++++++++++++++++++++++ OAM activate ++++++++++++++++++++++++
++++++++++++++++++++++++++++ OAM activated!!!! ++++++++++++++++++++++++
================== Short Packet Filter deactivated =============
================== ethernet OAM control =============
================== ADSL Detected ==================
================== packet filter configured =============
================== filter offset 1 configured =============, offset
================== filter offset 2 configured =============
================== packet filter activated =============
================== cell extraction configured 1 =============
================== cell extraction configured 2 =============
================== cell extraction configured 3 =============
================== cell extraction configured 4 =============
================== cell extraction configured 5 =============
================== cell extraction configured 6 =============
================== cell extraction configured 7 =============
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[41] found - skipped
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[12] found - skipped
VINAX_DRV[00]: BM-7 CS: EMPTY <data> page[13] found - skipped
nReturn=0 nData="0041 0000 0001 "
sCommand=DSL_CBS_LINE_STATE nLine=00 nLineState=00000200
dsl_daemon: new modem state 512
nReturn=0
[avm_debug]redirect kernel-messages (/dev/debug)f63b9e5e36124c80fe50b86692926db8 /lib/modules/c55fw.hex
[pcmlink]svn: 1263
[4294942079][isdn]svn:2743
driver params overwritten io_addr=0x0 irq_num=0
[4294942132]maxrun: 1
[pcmlink]c55_isr: d=00003f2a r=00003ee8 s=00003f00 m=00002108
[pcmlink]c55: simple checksum: 18DF2FE
[4294942172]PCMLINK: Version 5.362 Slots=13 BChan=11(Analog=3) DChan=2 Fifo=128 DSP-EC: 4
capicodec_init()
[capi_codec] support fax
[capi_codec] support Codecs
[4294942436][DECTDRV_ERR] avm_dect driver init
[4294942437][DECTDRV_ERR] [avm_dect]avm_dect_thread: start
dect_uicp_from_dect, ignore 15 bytes, dect_manager not up: 10 00 0B 00 00 0F 7B 2F
dect_uicp_from_dect, ignore 15 bytes, dect_manager not up: 10 00 0B 00 00 0F 7B 2Fcheckempty: : No such file or directory
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
musb_hdrc: version 2.2a/db-0.5.1, cppi-dma, host, debug=0
musb_hdrc: ConfigData=0x06 (UTMI-8, dyn FIFOs, SoftConn)
musb_hdrc: MHDRC RTL version 1.500
musb_hdrc: setup fifo_mode 2
musb_hdrc: 7/9 max ep, 2624/4096 memory
musb_hdrc: hw_ep 0shared, max 64
musb_hdrc: hw_ep 1tx, max 512
musb_hdrc: hw_ep 1rx, max 512
musb_hdrc: hw_ep 2tx, max 512
musb_hdrc: hw_ep 2rx, max 512
musb_hdrc: hw_ep 3shared, max 256
musb_hdrc: hw_ep 4shared, max 256
musb_hdrc: USB Host mode controller at A3400000 using DMA, IRQ 39
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detectedTI USB 2.0 Host started
/etc/init.d/rc.S: line 1863: cannot create /dev/new_led: No such device or address
/etc/init.d/rc.S: line 1863: cannot create /dev/new_led: No such device or address
/etc/init.d/rc.S: line 1863: cannot create /dev/new_led: No such device or address
open:: No such file or directory
/etc/init.d/rc.S: line 1868: cannot create /dev/new_led: No such device or address
/etc/init.d/rc.S: line 1873: cannot create /dev/new_led: No such device or address
/etc/init.d/rc.S: line 1875: cannot create /dev/new_led: No such device or address
/etc/init.d/rc.S: line 1877: cannot create /dev/new_led: No such device or address
/etc/init.d/rc.S: line 1879: cannot create /dev/new_led: No such device or address
dect_uicp_from_dect, ignore 23 bytes, dect_manager not up: 10 00 13 00 00 0F 14 F6
kdsldmod: init start (Nov 29 2010 15:17:33) sizeof(struct sk_buff)=168
kdsldmod: init donegrep: /var/flash/wlan.cfg: No such file or directory
/etc/init.d/rc.net: line 415: websrv: not found
Jan 1 01:00:57 ctlmgr[530]: load_config(wlan): factory default loaded
[avm_vinax] state request received.
[avm_vinax] event. < Size: 20 | Status: 1 | DS: 0 | US: 0 | dsl mode: ADSL>
eth: port 0 status 2 throttle 0
eth: port 1 status 1 throttle 1
eth: port 2 status 1 throttle 1
eth: port 3 status 1 throttle 1
[4294943171]DSP: XDU=1( D1) OVR=0 MIPS_OVR=0
[4294943180]maxrun: 3checkempty: : No such file or directory
[cpmac] [cpmac_main_ioctl] unknown ioctl 35142
device cpmac0 entered promiscuous mode
device eth0 entered promiscuous mode
device wan entered promiscuous mode
[avm_vinax] state request received.
[avm_vinax] event. < Size: 20 | Status: 1 | DS: 0 | US: 0 | dsl mode: ADSL>
[avm_vinax] state request received.
[avm_vinax] event. < Size: 20 | Status: 1 | DS: 0 | US: 0 | dsl mode: ADSL>
Jan 1 01:00:59 multid[542]: DHCPD on lan:0 skipped, is virtual interface
Jan 1 01:00:59 multid[542]: call pupnpdev_start_onlinestore
Jan 1 01:00:59 multid[542]: call pupnpdev_start_usb
Jan 1 01:00:59 multid[542]: DEBUG: upnpdev_start_usb
Jan 1 01:00:59 wlanconfig[555]: load_config(wlan): factory default loaded
dect_uicp_from_dect, ignore 23 bytes, dect_manager not up: 10 00 13 00 00 0F 14 F6
[cpmac] [cpmac_main_ioctl] unknown ioctl 35142
lan: port 1(eth0) entering learning state
lan: topology change detected, propagating
lan: port 1(eth0) entering forwarding state
dect_uicp_from_dect, ignore 23 bytes, dect_manager not up: 10 00 13 00 00 0F 14 F6
dect_uicp_from_dect, ignore 23 bytes, dect_manager not up: 10 00 13 00 00 0F 14 F6
dect_uicp_from_dect, ignore 23 bytes, dect_manager not up: 10 00 13 00 00 0F 14 F6MASTER_ENABLE wlan,
[4294945098]maxrun: 1SET wlan,0 = 1
[wlan_eeprom] calibration data blocks found = 1
[wlan_eeprom] Got calibration data version 2 for instance #1
[wlan_eeprom] Loading "/lib/modules/wlan_eeprom_hw0.bin"
[wlan_eeprom] Patching calibration data into eeprom
[wlan_eeprom] Patching MAC address to 00:1F:3F:A2:A7:49
[wlan_eeprom] Customer data="7270_V5B25_Dualband"
wlanfw: Init.
ath_hal: 0.9.14.25 (AR5416, REGOPS_FUNC)
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
wlan: 0.8.4.2 (Atheros/multi-bss)
Registered for AVM event source.
ath_rate_atheros: Version 2.0.1
Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved
ath_pci: 0.9.4.5 (Atheros/multi-bss)
ath_pci: CR-LSDK-1.3.1.146
cache line size: 16
[wlan_eeprom] EEPROM content 0x0200-0x0EB8 for instance 1 copied to driver
No MBSSID aggregation supportChan Freq RegPwr HT CTL CTL_U CTL_L DFS
1 2412n 20 HT20 1 0 1 N
2 2417n 20 HT20 1 0 1 N
3 2422n 20 HT40 1 0 1 N
4 2427n 20 HT40 1 0 1 N
5 2432n 20 HT40 1 1 1 N
6 2437n 20 HT40 1 1 1 N
7 2442n 20 HT40 1 1 1 N
8 2447n 20 HT40 1 1 1 N
9 2452n 20 HT40 1 1 1 N
10 2457n 20 HT40 1 1 0 N
11 2462n 20 HT40 1 1 0 N
12 2467n 20 HT20 1 1 0 N
13 2472n 20 HT20 1 1 0 N
36 5180n 30 HT20 1 0 1 N
38 5190n 20 HT40 1 0 0 N
40 5200n 30 HT20 1 1 0 N
44 5220n 30 HT20 1 0 1 N
46 5230n 20 HT40 1 0 0 N
48 5240n 30 HT20 1 1 0 N
52 5260n 20 HT20 1 0 1 Y
54 5270n 20 HT40 1 0 0 Y
56 5280n 20 HT20 1 1 0 Y
60 5300n 20 HT20 1 0 1 Y
62 5310n 20 HT40 1 0 0 Y
64 5320n 20 HT20 1 1 0 Y
100 5500n 27 HT20 1 0 1 Y
102 5510n 27 HT40 1 0 0 Y
104 5520n 27 HT20 1 1 0 Y
108 5540n 27 HT20 1 0 1 Y
110 5550n 27 HT40 1 0 0 Y
112 5560n 27 HT20 1 1 0 Y
116 5580n 27 HT20 1 0 1 Y
118 5590n 27 HT40 1 0 0 Y
120 5600n 27 HT20 1 1 0 Y
124 5620n 27 HT20 1 0 1 Y
126 5630n 27 HT40 1 0 0 Y
128 5640n 27 HT20 1 1 0 Y
132 5660n 27 HT20 1 0 1 Y
134 5670n 27 HT40 1 0 0 Y
136 5680n 27 HT20 1 1 0 Y
140 5700n 27 HT20 1 0 0 Y
(Rx) dd->dd_desc: B7FA3000, dd->dd_desc_paddr: 17FA3000, dd->dd_desc_len: 9000, *bf: 97FAD000
(Tx) dd->dd_desc: B7F60000, dd->dd_desc_paddr: 17F60000, dd->dd_desc_len: 23280, *bf: 97F84000
dfs_init_radar_filters: dfs->dfs_rinfo.rn_numradars: 0
DFS min filter rssiThresh = 21
DFS max pulse dur = 131 ticks
wifi0: 11na rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11na MCS: 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
wifi0: 11ng rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11ng MCS: 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
wifi0: mac 13.2 phy 8.1 radio 12.0
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Use hw queue 7 for UAPSD
avm_net_trace: New net trace device 'HW (2.4 + 5 GHz, wifi0)' registered with minor 128.
wifi0: Atheros 5416 PCI: mem=0x40000000, irq=80 hw_base=0xC0420000
wlan: mac acl policy registered
avm_net_trace: New net trace device 'AP (2.4 + 5 GHz, ath0)' registered with minor 130.
avm_net_trace: New net trace device 'AP (2.4 + 5 GHz, ath0)' registered with minor 131.
dect_uicp_from_dect, ignore 23 bytes, dect_manager not up: 10 00 13 00 00 0F 14 F6
userman: LAN Client Internet-Accounting and Blocking
userman: device registerd with major=228
userman: init ok
device ath0 entered promiscuous mode
lan: port 2(ath0) entering learning state
lan: topology change detected, propagating
lan: port 2(ath0) entering forwarding stateSET wlan,0 = MASTER_DISABLE wlan,Jan 1 01:01:22 dsld[1265]: voip: ppptarget voip disabled, ignored
[avm_vinax] state request received.
[avm_vinax] event. < Size: 20 | Status: 1 | DS: 0 | US: 0 | dsl mode: ADSL>
[avm_vinax] state request received.
[avm_vinax] event. < Size: 20 | Status: 1 | DS: 0 | US: 0 | dsl mode: ADSL>
Jan 1 01:01:23 telefon[1271]: use clock_gettime(CLOCK_MONOTONIC)!
Jan 1 01:01:23 telefon[1271]: NoOldMSNNames
Jan 1 01:01:23 telefon[1271]: SIGCHLD received!
Jan 1 01:01:23 telefon[1271]: WARNING No config file '/var/flash/fx_def' !
Jan 1 01:01:23 telefon[1271]: WARNING No CG file '/var/flash/fx_cg' !
[capi_oslib] capi_installed
[capi_oslib] capi_installedcreate sema UPNPAPI_DATA_phonebook
/sbin/start_plugin.sh[1294]: Plugins awaited: mini onlinepb ntfs samba
run_clock demon started
AVM_WATCHDOG: System Init UEberwachung abgeschlossen (173660 ms noch verfuegbar)
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_cpuclock: norm_power_rate=100 act_rate=100 mul=0 div=1 offset=0 NormP=0 mW -> SumNormP=0 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_systemclock: norm_power_rate=100 act_rate=100 mul=65 div=10 offset=1793 NormP=2443 mW -> SumNormP=2443 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_wlan: norm_power_rate=100 act_rate=100 mul=84 div=10 offset=100 NormP=940 mW -> SumNormP=3383 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_isdnnt: norm_power_rate=100 act_rate=0 mul=1 div=1 offset=0 NormP=100 mW -> SumNormP=3483 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_isdnte: norm_power_rate=100 act_rate=0 mul=1 div=1 offset=0 NormP=100 mW -> SumNormP=3583 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_analog: norm_power_rate=200 act_rate=0 mul=141 div=10 offset=100 NormP=2920 mW -> SumNormP=6503 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_dect: norm_power_rate=100 act_rate=0 mul=200 div=78 offset=150 NormP=406 mW -> SumNormP=6909 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_ethernet: norm_power_rate=467 act_rate=1258291631 mul=1 div=1 offset=50 NormP=517 mW -> SumNormP=7426 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_dsl: norm_power_rate=100 act_rate=0 mul=15 div=1 offset=0 NormP=1500 mW -> SumNormP=8926 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_usb_host: norm_power_rate=500 act_rate=0 mul=55 div=10 offset=0 NormP=2750 mW -> SumNormP=11676 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_usb_client: norm_power_rate=0 act_rate=0 mul=0 div=1 offset=0 NormP=0 mW -> SumNormP=11676 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_charge: norm_power_rate=446 act_rate=0 mul=0 div=1 offset=0 NormP=0 mW -> SumNormP=11676 mW
[avm_power] pm_ressourceinfo_scriptparse: powerdevice_loadrate: norm_power_rate=100 act_rate=100 mul=29 div=10 offset=-17 NormP=273 mW -> SumNormP=11949 mW
SysRq : Changing Loglevel
Loglevel set to 4Info: have to stop cat /dev/debug.
/etc/init.d/rc.S[106]: trigger: msgsend ctlmgr init-done
/etc/init.d/rc.S[106]: trigger: msgsend ctlmgr check-plugins
Please press Enter to activate this console.
dect_uicp_from_dect, ignore 23 bytes, dect_manager not up: 10 00 13 00 00 0F 14 F6cat: read error: Broken pipe
/sbin/start_plugin.sh[1337]: Plugins awaited: mini onlinepb ntfs samba
Jan 1 01:01:26 telefon[1275]: SIGCHLD received!
/sbin/start_plugin.sh[1337]: Extract SOFTWARE-PLUGIN file:///data/plugins.update
ERROR file not found (ftp, file, http)
/sbin/start_plugin.sh[1337]: ACHTUNG: es ist ein Fehler aufgetreten.
Jan 1 01:01:27 telefon[1275]: Stop DECT
/sbin/start_plugin.sh[1400]: Plugins awaited: mini onlinepb ntfs samba
/sbin/start_plugin.sh[1400]: searching Mount Point ...
Jan 1 01:01:47 telefon[1275]: SIGCHILD killdectpid
DSL: ++++++++++++++++ loading ADSL FW ++++++++++++++++++++
DSL: ++++++++++++++++ loading ADSL FW ++++++++++++++++++++
file path is /lib/modules/vinax_fw_adsl.bin
fw size is 0
DSL: loading firmware binary /lib/modules/vinax_fw_adsl.bin
DSL: firmware binary size 540916 bytes
DSL[00]: Device Start EVT - UsrRst, DrvState 1 --> 1
DSL[00]: Line in reset - block!
DSL[00]: VINAX line recovered.
sCommand=DSL_CBS_LINE_STATE nLine=00 nLineState=00000100
dsl_daemon: new modem state 256
Setting inventory DSL-FW version number to 9.5.2.1.1.6
sCommand=DSL_CBS_LINE_STATE nLine=00 nLineState=00000200
dsl_daemon: new modem state 512
Jan 1 01:08:12 multid[3157]: DHCPD on lan:0 skipped, is virtual interface
Jan 1 01:08:12 multid[3157]: call pupnpdev_start_onlinestore
Jan 1 01:08:12 multid[3157]: call pupnpdev_start_usb
Jan 1 01:08:12 multid[3157]: DEBUG: upnpdev_start_usb
Aug 23 22:45:50 telefon[1275]: set initial telefon time from linux time to 22:45:50 23.08 2011!
DSL: ++++++++++++++++ loading ADSL FW ++++++++++++++++++++
DSL: ++++++++++++++++ loading ADSL FW ++++++++++++++++++++
file path is /lib/modules/vinax_fw_adsl.bin
fw size is 0
DSL: loading firmware binary /lib/modules/vinax_fw_adsl.bin
DSL: firmware binary size 540916 bytes
DSL[00]: Device Start EVT - UsrRst, DrvState 1 --> 1
DSL[00]: Line in reset - block!
DSL[00]: VINAX line recovered.
sCommand=DSL_CBS_LINE_STATE nLine=00 nLineState=00000100
dsl_daemon: new modem state 256
Setting inventory DSL-FW version number to 9.5.2.1.1.6
sCommand=DSL_CBS_LINE_STATE nLine=00 nLineState=00000200
dsl_daemon: new modem state 512
/sbin/start_plugin.sh[3214]: Plugins awaited: mini onlinepb ntfs samba
/sbin/start_plugin.sh[3214]: External get & install
script url="http://boxplugin.avm.de./cgi-bin/boxplugin?name=FRITZ!Box+Fon+WLAN+7270+v1&revision=18902&version=54.04.88&subversion=&hw=122&OEM=avm"
ok
Plugin found at URL="http://boxplugin.avm.de/boxplugin/122/54.04.88/18902..avm.plugin"
/sbin/start_plugin.sh[3214]: External get from 'http://boxplugin.avm.de/boxplugin/122/54.04.88/18902..avm.plugin', try to save to '/var/tmp/plugins.update'
/sbin/start_plugin.sh[3214]: Extract SOFTWARE-PLUGIN http://boxplugin.avm.de/boxplugin/122/54.04.88/18902..avm.plugin/plugins.update
/sbin/start_plugin.sh[3214]: ... option savefile '/var/tmp/plugins.update' found
./var/
./var/plugin-ntfs.image
./var/plugin-webdav.image
./var/plugin-tam.image
./var/plugin-samba.image
./var/install
./var/plugin-onlinepb.image
./var/plugin-mediasrv.image
./var/plugin-mini.image
./var/signature
/sbin/start_plugin.sh[3214]: calling local storage handler with savefile '/var/tmp/plugins.update'...
/sbin/start_plugin.sh[3214]: attempt to store plugin to buildin flash
/sbin/start_plugin.sh[3214]: cp '/var/tmp/plugins.update' to '/data/plugins.update'
/sbin/start_plugin.sh[3214]: Prepare SOFTWARE-PLUGIN mediasrv ...
/sbin/start_plugin.sh[3214]: Mount SOFTWARE-PLUGIN mediasrv ...
next free loop devive: /dev/loop0
/sbin/start_plugin.sh[3214]: Prepare SOFTWARE-PLUGIN mini ...
/sbin/start_plugin.sh[3214]: Mount SOFTWARE-PLUGIN mini ...
/dev/loop0 on /var/plugin-mediasrv type squashfs (ro)
next free loop devive: /dev/loop1
/sbin/start_plugin.sh[3214]: Prepare SOFTWARE-PLUGIN ntfs ...
/sbin/start_plugin.sh[3214]: Mount SOFTWARE-PLUGIN ntfs ...
/dev/loop0 on /var/plugin-mediasrv type squashfs (ro)
/dev/loop1 on /var/plugin-mini type squashfs (ro)
next free loop devive: /dev/loop2
/sbin/start_plugin.sh[3214]: Prepare SOFTWARE-PLUGIN onlinepb ...
/sbin/start_plugin.sh[3214]: Mount SOFTWARE-PLUGIN onlinepb ...
/dev/loop0 on /var/plugin-mediasrv type squashfs (ro)
/dev/loop1 on /var/plugin-mini type squashfs (ro)
/dev/loop2 on /var/plugin-ntfs type squashfs (ro)
next free loop devive: /dev/loop3
/sbin/start_plugin.sh[3214]: Prepare SOFTWARE-PLUGIN samba ...
/sbin/start_plugin.sh[3214]: Mount SOFTWARE-PLUGIN samba ...
/dev/loop0 on /var/plugin-mediasrv type squashfs (ro)
/dev/loop1 on /var/plugin-mini type squashfs (ro)
/dev/loop2 on /var/plugin-ntfs type squashfs (ro)
/dev/loop3 on /var/plugin-onlinepb type squashfs (ro)
next free loop devive: /dev/loop4
/sbin/start_plugin.sh[3214]: Prepare SOFTWARE-PLUGIN tam ...
/sbin/start_plugin.sh[3214]: Mount SOFTWARE-PLUGIN tam ...
/dev/loop0 on /var/plugin-mediasrv type squashfs (ro)
/dev/loop1 on /var/plugin-mini type squashfs (ro)
/dev/loop2 on /var/plugin-ntfs type squashfs (ro)
/dev/loop3 on /var/plugin-onlinepb type squashfs (ro)
/dev/loop4 on /var/plugin-samba type squashfs (ro)
next free loop devive: /dev/loop5
/sbin/start_plugin.sh[3214]: Prepare SOFTWARE-PLUGIN webdav ...
/sbin/start_plugin.sh[3214]: Mount SOFTWARE-PLUGIN webdav ...
/dev/loop0 on /var/plugin-mediasrv type squashfs (ro)
/dev/loop1 on /var/plugin-mini type squashfs (ro)
/dev/loop2 on /var/plugin-ntfs type squashfs (ro)
/dev/loop3 on /var/plugin-onlinepb type squashfs (ro)
/dev/loop4 on /var/plugin-samba type squashfs (ro)
/dev/loop5 on /var/plugin-tam type squashfs (ro)
next free loop devive: /dev/loop6
/sbin/start_plugin.sh[3214]: Start SOFTWARE-PLUGIN mediasrv ...
Starte Mediaserver Plugin.
start morphstick extensions
/sbin/start_plugin.sh[3214]: Start SOFTWARE-PLUGIN mini ...
Starte Mini Plugin.
/sbin/start_plugin.sh[3214]: Start SOFTWARE-PLUGIN ntfs ...
Starte NTFS-3G Plugin.
/sbin/start_plugin.sh[3214]: Start SOFTWARE-PLUGIN onlinepb ...
Starte Onlinepb Plugin.
/sbin/start_plugin.sh[3214]: Start SOFTWARE-PLUGIN samba ...
Starte Samba Plugin.
/sbin/start_plugin.sh[3214]: Start SOFTWARE-PLUGIN tam ...
Starte TAM Plugin.
start audiod extensions
/sbin/start_plugin.sh[3214]: Start SOFTWARE-PLUGIN webdav ...
cat: can't open '/var/USB-proc-bus-*-storage': No such file or directory
NTFS mount retry: /proc/bus/*/storage sdev:
Starte Webdav Plugin.
SCSI device still not ready, wait some extra time
SCSI device still not ready, wait some extra time
SCSI device still not ready, wait some extra time
SCSI device still not ready, wait some extra time
SCSI device still not ready, wait some extra time
SCSI device still not ready, wait some extra time
SCSI device still not ready, wait some extra time
SCSI device still not ready, wait some extra time
SCSI device still not ready, wait some extra time
SCSI device still not ready, wait some extra time
No partition(s) found!
