misdn & hylafax - abbruch beim senden

[Holg]

Hallo,

Ich habe ein elastix aufgesetzt mit misdn - läuft soweit auch wunderbar. Mein Problem ist nur, dass ich wenn ich über eine Clientsoftware ein Fax über hylafax schicken will, die Kommunikation abgebrochen wird. Kann das ein Problem mit dem mISDN-Treiber sein?
Bin ein wenig ratlos...

hier mal das Hylafax-Log beim rausfaxen.

Jun 30 09:44:18.74: [29715]: SESSION BEGIN 000000044 59304031013332
Jun 30 09:44:18.74: [29715]: HylaFAX (tm) Version 4.3.3
Jun 30 09:44:18.74: [29715]: SEND FAX: JOB 16 DEST 031013332 COMMID 000000044 DEVICE '/dev/ttyIAX1' FROM 'root <[email protected]>' USER root
Jun 30 09:44:18.74: [29715]: STATE CHANGE: RUNNING -> SENDING
Jun 30 09:44:18.75: [29715]: <-- [12:AT+FCLASS=1\r]
Jun 30 09:44:18.75: [29715]: --> [2:OK]
Jun 30 09:44:18.75: [29715]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Jun 30 09:44:18.76: [29715]: DIAL 031013332
Jun 30 09:44:18.76: [29715]: <-- [14:ATDT031013332\r]
Jun 30 09:44:24.99: [29715]: --> [7:CONNECT]
Jun 30 09:44:26.83: [29715]: --> HDLC<34:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 2C 74 CC 74 CC DA 7F>
Jun 30 09:44:26.83: [29715]: --> [2:OK]
Jun 30 09:44:26.83: [29715]: REMOTE NSF "AD 00 55 48 79 6C 61 46 41 58 20 28 74 6D 29 20 56 65 72 73 69 6F 6E 20 34 2E 33 2E 33"
Jun 30 09:44:26.83: [29715]: NSF remote fax equipment: HylaFAX 
Jun 30 09:44:26.83: [29715]: NSF remote station ID: "HylaFAX (tm) Version 4.3.3"
Jun 30 09:44:26.83: [29715]: <-- [9:AT+FRH=3\r]
Jun 30 09:44:26.85: [29715]: --> [7:CONNECT]
Jun 30 09:44:27.65: [29715]: --> HDLC<25:FF C0 02 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 A4 F3>
Jun 30 09:44:27.65: [29715]: --> [2:OK]
Jun 30 09:44:27.65: [29715]: REMOTE CSI ""
Jun 30 09:44:27.65: [29715]: <-- [9:AT+FRH=3\r]
Jun 30 09:44:27.69: [29715]: --> [7:CONNECT]
Jun 30 09:44:28.23: [29715]: --> HDLC<15:FF C8 01 00 73 5F 23 01 FB C1 01 01 18 90 61>
Jun 30 09:44:28.29: [29715]: --> [2:OK]
Jun 30 09:44:28.29: [29715]: REMOTE best rate 9600 bit/s
Jun 30 09:44:28.29: [29715]: REMOTE max A3 page width (303 mm)
Jun 30 09:44:28.29: [29715]: REMOTE max unlimited page length
Jun 30 09:44:28.29: [29715]: REMOTE best vres R16 x 15.4 line/mm
Jun 30 09:44:28.29: [29715]: REMOTE format support: MH, MR, MMR
Jun 30 09:44:28.29: [29715]: REMOTE supports T.30 Annex A, 256-byte ECM
Jun 30 09:44:28.29: [29715]: REMOTE best 0 ms/scanline
Jun 30 09:44:28.29: [29715]: USE 9600 bit/s
Jun 30 09:44:28.29: [29715]: USE error correction mode
Jun 30 09:44:28.29: [29715]: <-- [9:AT+FTH=3\r]
Jun 30 09:44:28.31: [29715]: --> [7:CONNECT]
Jun 30 09:44:28.31: [29715]: <-- HDLC<3:FF C8 DF>
Jun 30 09:44:29.49: [29715]: --> [2:OK]
Jun 30 09:44:29.49: [29715]: MODEM input buffering enabled
Jun 30 09:44:29.49: [29715]: <-- [5:ATH0\r]
Jun 30 09:44:29.59: [29715]: --> [2:OK]
Jun 30 09:44:29.59: [29715]: MODEM set DTR OFF
Jun 30 09:44:29.59: [29715]: MODEM set baud rate: 0 baud (flow control unchanged)
Jun 30 09:44:29.59: [29715]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Jun 30 09:44:29.59: [29715]: SESSION END

und hier was mir das cli verrät:
Er legt ein paar Sekunden nach der Verbindungsherstellung einfach auf.

-- mISDN/1-u226 is ringing
    -- mISDN/1-u226 answered IAX2/42-2
  == Spawn extension (macro-dialout-trunk, s, 27) exited non-zero on 'IAX2/42-2' in macro 'dialout-trunk'
  == Spawn extension (macro-dialout-trunk, s, 27) exited non-zero on 'IAX2/42-2'
    -- Executing [h@macro-dialout-trunk:1] Macro("IAX2/42-2", "hangupcall") in new stack
    -- Executing [s@macro-hangupcall:1] ResetCDR("IAX2/42-2", "w") in new stack
    -- Executing [s@macro-hangupcall:2] NoCDR("IAX2/42-2", "") in new stack
    -- Executing [s@macro-hangupcall:3] GotoIf("IAX2/42-2", "1?skiprg") in new stack
    -- Goto (macro-hangupcall,s,6)
    -- Executing [s@macro-hangupcall:6] GotoIf("IAX2/42-2", "1?theend") in new stack
    -- Goto (macro-hangupcall,s,9)
    -- Executing [s@macro-hangupcall:9] Wait("IAX2/42-2", "5") in new stack
  == Spawn extension (macro-hangupcall, s, 9) exited non-zero on 'IAX2/42-2' in macro 'hangupcall'
  == Spawn extension (macro-hangupcall, s, 9) exited non-zero on 'IAX2/42-2'
    -- Hungup 'IAX2/42-2'