; CAPI config
;
;
; general section
[general]
nationalprefix=0 ; or for example "+49"
internationalprefix=00 ; or for example "+"
;subscriberprefix=+4969 ; prefix including area code (some lines need this)
rxgain=1.0 ;linear receive gain (1.0 = no change)
txgain=1.0 ;linear transmit gain (1.0 = no change)
language=de ;set default language
;ulaw=yes ;set this, if you live in u-law world instead of a-law
;jb..... ;with Asterisk 1.4 you can configure jitterbuffer,
;see Asterisk documentation for all jb* setting available.
;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold.
; interface sections ...
[ISDN1] ;this example interface gets name 'ISDN1' and may be any
;name not starting with 'g' or 'contr'.
;Use one interface section for each isdn port!
ntmode=no ;if isdn card operates in nt mode, set this to yes
isdnmode=DID ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
;when using NT-mode, 'DID' should be set in any case
incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = any
;defaultcid=123 ;set a default caller id to that interface for dial-out,
;this caller id will be used when dial option 'd' is set.
;controller=0 ;ISDN4BSD default
;controller=7 ;ISDN4BSD USB default
controller=1 ;capi controller number of this interface/port
group=0 ;dialout group
;prefix=0 ;set a prefix to calling number on incoming calls
softdtmf=on ;enable/disable software dtmf detection, recommended for AVM cards
relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf detection
faxdetect=off ;enable faxdetection and redirection to EXTEN 'fax' for incoming and/or
;outgoing calls. (default='off', possible values: 'incoming','outgoing','both')
faxdetecttime=0 ;Only detect faxes during the first 'n' seconds of the call.
;(default '0' meaning for the whole duration of the call)
accountcode= ;PBX accountcode to use in CDRs
;amaflags=default;AMA flags for CDR ('default', 'omit', 'billing', or 'documentation')
context=capi-in ;context for incoming calls
;holdtype=hold ;when the PBX puts the call on hold, ISDN HOLD will be used. If
;set to 'local' (default value), no hold is done and the PBX may
;play MOH.
;immediate=yes ;DID: immediate start of pbx with extension 's' if no digits were
; received on incoming call (no destination number yet)
;MSN: start pbx on CONNECT_IND and don't wait for SETUP/SENDING-COMPLETE.
; info like REDIRECTINGNUMBER may be lost, but this is necessary for
; drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE.
;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression. Disable this before you start recording voicemail
;or your files may get choppy. (you can use capicommand(echosquelch|no) for this)
echocancel=yes ;Dialogic Diva (Capi) echo cancelation (yes=g165)
;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)
;echotail=64 ;echo cancel tail setting (default=0 for maximum)
;echocancelnlp=1 ;activate non-linear-processing; this improves echo cancel ratio, but might
;incorporate variable gain in the signal path.
bridge=yes ;native bridging (CAPI line interconnect) if available
callgroup=1 ;PBX call group
;pickupgroup=1 ;PBX pickup group (which call groups are we allowed to pickup)
;transfergroup=1 ;Controller(s) where a transfer on native bridge is allowed to.
language=de ;set language for this device (overwrites default language)
;disallow=all ;RTP codec selection (valid with Dialogic Diva only)
;allow=all ;RTP codec selection (valid with Dialogic Diva only)
devices=2 ;number of concurrent calls (b-channels) on this controller
;(2 makes sense for single BRI, 30/23 for PRI/T1)
;jb..... ;with Asterisk 1.4 you can configure jitterbuffer,
;see Asterisk documentation for all jb* setting available.
;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold.
;qsig=1 ;enable use of Q.SIG extensions. ECMA Variant
;qsig_prnum=1234 ;enable inbound bridging - this should be an QSIG-network-wide unique number
[ISDN2] ;this example interface gets name 'ISDN1' and may be any
;name not starting with 'g' or 'contr'.
;Use one interface section for each isdn port!
ntmode=no ;if isdn card operates in nt mode, set this to yes
isdnmode=DID ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
;when using NT-mode, 'DID' should be set in any case
incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = any
;defaultcid=123 ;set a default caller id to that interface for dial-out,
;this caller id will be used when dial option 'd' is set.
;controller=0 ;ISDN4BSD default
;controller=7 ;ISDN4BSD USB default
controller=2 ;capi controller number of this interface/port
group=0 ;dialout group
;prefix=0 ;set a prefix to calling number on incoming calls
softdtmf=on ;enable/disable software dtmf detection, recommended for AVM cards
relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf detection
faxdetect=off ;enable faxdetection and redirection to EXTEN 'fax' for incoming and/or
;outgoing calls. (default='off', possible values: 'incoming','outgoing','both')
faxdetecttime=0 ;Only detect faxes during the first 'n' seconds of the call.
;(default '0' meaning for the whole duration of the call)
accountcode= ;PBX accountcode to use in CDRs
;amaflags=default;AMA flags for CDR ('default', 'omit', 'billing', or 'documentation')
context=capi-in ;context for incoming calls
;holdtype=hold ;when the PBX puts the call on hold, ISDN HOLD will be used. If
;set to 'local' (default value), no hold is done and the PBX may
;play MOH.
;immediate=yes ;DID: immediate start of pbx with extension 's' if no digits were
; received on incoming call (no destination number yet)
;MSN: start pbx on CONNECT_IND and don't wait for SETUP/SENDING-COMPLETE.
; info like REDIRECTINGNUMBER may be lost, but this is necessary for
; drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE.
;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression. Disable this before you start recording voicemail
;or your files may get choppy. (you can use capicommand(echosquelch|no) for this)
echocancel=yes ;Dialogic Diva (Capi) echo cancelation (yes=g165)
;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)
;echotail=64 ;echo cancel tail setting (default=0 for maximum)
;echocancelnlp=1 ;activate non-linear-processing; this improves echo cancel ratio, but might
;incorporate variable gain in the signal path.
bridge=yes ;native bridging (CAPI line interconnect) if available
;callgroup=1 ;PBX call group
;pickupgroup=1 ;PBX pickup group (which call groups are we allowed to pickup)
;transfergroup=1 ;Controller(s) where a transfer on native bridge is allowed to.
language=de ;set language for this device (overwrites default language)
;disallow=all ;RTP codec selection (valid with Dialogic Diva only)
;allow=all ;RTP codec selection (valid with Dialogic Diva only)
devices=2 ;number of concurrent calls (b-channels) on this controller
;(2 makes sense for single BRI, 30/23 for PRI/T1)
;jb..... ;with Asterisk 1.4 you can configure jitterbuffer,
;see Asterisk documentation for all jb* setting available.
;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold.
;qsig=1 ;enable use of Q.SIG extensions. ECMA Variant
;qsig_prnum=1234 ;enable inbound bridging - this should be an QSIG-network-wide unique number
[ISDN3] ;this example interface gets name 'ISDN1' and may be any
;name not starting with 'g' or 'contr'.
;Use one interface section for each isdn port!
ntmode=no ;if isdn card operates in nt mode, set this to yes
isdnmode=DID ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
;when using NT-mode, 'DID' should be set in any case
incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = any
;defaultcid=123 ;set a default caller id to that interface for dial-out,
;this caller id will be used when dial option 'd' is set.
;controller=0 ;ISDN4BSD default
;controller=7 ;ISDN4BSD USB default
controller=3 ;capi controller number of this interface/port
group=0 ;dialout group
;prefix=0 ;set a prefix to calling number on incoming calls
softdtmf=on ;enable/disable software dtmf detection, recommended for AVM cards
relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf detection
faxdetect=off ;enable faxdetection and redirection to EXTEN 'fax' for incoming and/or
;outgoing calls. (default='off', possible values: 'incoming','outgoing','both')
faxdetecttime=0 ;Only detect faxes during the first 'n' seconds of the call.
;(default '0' meaning for the whole duration of the call)
accountcode= ;PBX accountcode to use in CDRs
;amaflags=default;AMA flags for CDR ('default', 'omit', 'billing', or 'documentation')
context=capi-in ;context for incoming calls
;holdtype=hold ;when the PBX puts the call on hold, ISDN HOLD will be used. If
;set to 'local' (default value), no hold is done and the PBX may
;play MOH.
;immediate=yes ;DID: immediate start of pbx with extension 's' if no digits were
; received on incoming call (no destination number yet)
;MSN: start pbx on CONNECT_IND and don't wait for SETUP/SENDING-COMPLETE.
; info like REDIRECTINGNUMBER may be lost, but this is necessary for
; drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE.
;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression. Disable this before you start recording voicemail
;or your files may get choppy. (you can use capicommand(echosquelch|no) for this)
echocancel=yes ;Dialogic Diva (Capi) echo cancelation (yes=g165)
;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)
;echotail=64 ;echo cancel tail setting (default=0 for maximum)
;echocancelnlp=1 ;activate non-linear-processing; this improves echo cancel ratio, but might
;incorporate variable gain in the signal path.
bridge=yes ;native bridging (CAPI line interconnect) if available
;callgroup=1 ;PBX call group
;pickupgroup=1 ;PBX pickup group (which call groups are we allowed to pickup)
;transfergroup=1 ;Controller(s) where a transfer on native bridge is allowed to.
language=de ;set language for this device (overwrites default language)
;disallow=all ;RTP codec selection (valid with Dialogic Diva only)
;allow=all ;RTP codec selection (valid with Dialogic Diva only)
devices=2 ;number of concurrent calls (b-channels) on this controller
;(2 makes sense for single BRI, 30/23 for PRI/T1)
;jb..... ;with Asterisk 1.4 you can configure jitterbuffer,
;see Asterisk documentation for all jb* setting available.
;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold.
;qsig=1 ;enable use of Q.SIG extensions. ECMA Variant
;qsig_prnum=1234 ;enable inbound bridging - this should be an QSIG-network-wide unique number
[ISDN4] ;this example interface gets name 'ISDN1' and may be any
;name not starting with 'g' or 'contr'.
;Use one interface section for each isdn port!
ntmode=yes ;if isdn card operates in nt mode, set this to yes
isdnmode=DID ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
;when using NT-mode, 'DID' should be set in any case
incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = any
;defaultcid=123 ;set a default caller id to that interface for dial-out,
;this caller id will be used when dial option 'd' is set.
;controller=0 ;ISDN4BSD default
;controller=7 ;ISDN4BSD USB default
controller=4 ;capi controller number of this interface/port
group=1 ;dialout group
;prefix=0 ;set a prefix to calling number on incoming calls
softdtmf=on ;enable/disable software dtmf detection, recommended for AVM cards
relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf detection
faxdetect=off ;enable faxdetection and redirection to EXTEN 'fax' for incoming and/or
;outgoing calls. (default='off', possible values: 'incoming','outgoing','both')
faxdetecttime=0 ;Only detect faxes during the first 'n' seconds of the call.
;(default '0' meaning for the whole duration of the call)
accountcode= ;PBX accountcode to use in CDRs
;amaflags=default;AMA flags for CDR ('default', 'omit', 'billing', or 'documentation')
context=capi-in ;context for incoming calls
;holdtype=hold ;when the PBX puts the call on hold, ISDN HOLD will be used. If
;set to 'local' (default value), no hold is done and the PBX may
;play MOH.
;immediate=yes ;DID: immediate start of pbx with extension 's' if no digits were
; received on incoming call (no destination number yet)
;MSN: start pbx on CONNECT_IND and don't wait for SETUP/SENDING-COMPLETE.
; info like REDIRECTINGNUMBER may be lost, but this is necessary for
; drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE.
;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression. Disable this before you start recording voicemail
;or your files may get choppy. (you can use capicommand(echosquelch|no) for this)
echocancel=yes ;Dialogic Diva (Capi) echo cancelation (yes=g165)
;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)
;echotail=64 ;echo cancel tail setting (default=0 for maximum)
;echocancelnlp=1 ;activate non-linear-processing; this improves echo cancel ratio, but might
;incorporate variable gain in the signal path.
bridge=yes ;native bridging (CAPI line interconnect) if available
;callgroup=1 ;PBX call group
;pickupgroup=1 ;PBX pickup group (which call groups are we allowed to pickup)
;transfergroup=1 ;Controller(s) where a transfer on native bridge is allowed to.
language=de ;set language for this device (overwrites default language)
;disallow=all ;RTP codec selection (valid with Dialogic Diva only)
;allow=all ;RTP codec selection (valid with Dialogic Diva only)
devices=2 ;number of concurrent calls (b-channels) on this controller
;(2 makes sense for single BRI, 30/23 for PRI/T1)
;jb..... ;with Asterisk 1.4 you can configure jitterbuffer,
;see Asterisk documentation for all jb* setting available.
;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold.
;qsig=1 ;enable use of Q.SIG extensions. ECMA Variant
;qsig_prnum=1234 ;enable inbound bridging - this should be an QSIG-network-wide unique number
extension_custom.conf
; This file contains example extensions_custom.conf entries.
; extensions_custom.conf should be used to include customizations
; to AMP's Asterisk dialplan.
; All custom context should contain the string 'custom' in it's name
; Extensions in AMP have access to the 'from-internal' context.
; The context 'from-internal-custom' is included in 'from-internal' by default
#include extensions_hud.conf
;Eintrag am 18.11.08/Thurn
[general]
static=yes
writeprotect=no
[capi-out]
exten=> Dial(CAPI/contr1/${EXTEN}/tr)
exten=> Dial(CAPI/contr2/${EXTEN}/tr)
exten=> Dial(CAPI/contr3/${EXTEN}/tr)
[capi-in]
exten => 23,1,Dial(SIP/23,tr)
;Eintrag Ende
[from-internal-custom]
;1234,1,Playback(demo-congrats) ; extensions can dial 1234
;1234,2,Hangup()
;h,1,Hangup()
;include => custom-recordme ; extensions can also dial 5678
; custom-count2four,s,1 can be used as a custom target for
; a Digital Receptionist menu or a Call Group
;[custom-count2four]
;s,1,SayDigits(1234)
;s,2,Hangup
; custom-recordme,5678,1 can be used as a custom target for
; a Digital Receptionist menu or a Call Group
;[custom-recordme]
;exten => 5678,1,Wait(2)
;exten => 5678,2,Record(/tmp/asterisk-recording:gsm)
;exten => 5678,3,Wait(2)
;exten => 5678,4,Playback(/tmp/asterisk-recording)
;exten => 5678,5,Wait(2)
;exten => 5678,6,Hangup
[custom-meetme3]
exten => s,1,Answer
exten => s,n,Wait(3)
exten => s,n,CBMysql()
exten => s,n,Hangup
