Trixbox Pro 1.1.3 mit AVM C2

[Hotz87]

Hallo,

ich habe das Problem das ich die AVM C2 Karte nicht bei Trixbox im Webinterface eingezeigt bekomme, ich poste euch mal nen paar Ausgaben.

lspci -v

01:09.0 I2O: Digital Equipment Corporation StrongARM DC21285 (rev 04) (prog-if 01)
        Subsystem: AVM Audiovisuelles MKTG & Computer System GmbH: Unknown device 1100
        Flags: bus master, medium devsel, latency 64, IRQ 145
        Memory at febdef80 (32-bit, non-prefetchable) [size=128]
        I/O ports at 7880 [size=128]
        Capabilities: [70] Power Management version 2

capiinfo

[root@trixbox112920 asterisk]# capiinfo
Number of Controllers : 2
Controller 1:
Manufacturer: AVM GmbH
CAPI Version: 2.0
Manufacturer Version: 3.11-06  (49.22)
Serial Number: 1070969
BChannels: 2
Global Options: 0x00000039
   internal controller supported
   DTMF supported
   Supplementary Services supported
   channel allocation supported (leased lines)
B1 protocols support: 0x4000011f
   64 kbit/s with HDLC framing
   64 kbit/s bit-transparent operation
   V.110 asynconous operation with start/stop byte framing
   V.110 synconous operation with HDLC framing
   T.30 modem for fax group 3
   Modem asyncronous operation with start/stop byte framing
B2 protocols support: 0x00000b1b
   ISO 7776 (X.75 SLP)
   Transparent
   LAPD with Q.921 for D channel X.25 (SAPI 16)
   T.30 for fax group 3
   ISO 7776 (X.75 SLP) with V.42bis compression
   V.120 asyncronous mode
   V.120 bit-transparent mode
B3 protocols support: 0x800000bf
   Transparent
   T.90NL, T.70NL, T.90
   ISO 8208 (X.25 DTE-DTE)
   X.25 DCE
   T.30 for fax group 3
   T.30 for fax group 3 with extensions
   Modem

  0100
  0200
  39000000
  1f010040
  1b0b0000
  bf000080
  00000000 00000000 00000000 00000000 00000000 00000000
  01000001 00020000 00000000 00000000 00000000

Supplementary services support: 0x000003ff
   Hold / Retrieve
   Terminal Portability
   ECT
   3PTY
   Call Forwarding
   Call Deflection
   MCID
   CCBS

Controller 2:
Manufacturer: AVM GmbH
CAPI Version: 2.0
Manufacturer Version: 3.11-06  (49.22)
Serial Number: 1070969
BChannels: 2
Global Options: 0x00000039
   internal controller supported
   DTMF supported
   Supplementary Services supported
   channel allocation supported (leased lines)
B1 protocols support: 0x4000011f
   64 kbit/s with HDLC framing
   64 kbit/s bit-transparent operation
   V.110 asynconous operation with start/stop byte framing
   V.110 synconous operation with HDLC framing
   T.30 modem for fax group 3
   Modem asyncronous operation with start/stop byte framing
B2 protocols support: 0x00000b1b
   ISO 7776 (X.75 SLP)
   Transparent
   LAPD with Q.921 for D channel X.25 (SAPI 16)
   T.30 for fax group 3
   ISO 7776 (X.75 SLP) with V.42bis compression
   V.120 asyncronous mode
   V.120 bit-transparent mode
B3 protocols support: 0x800000bf
   Transparent
   T.90NL, T.70NL, T.90
   ISO 8208 (X.25 DTE-DTE)
   X.25 DCE
   T.30 for fax group 3
   T.30 for fax group 3 with extensions
   Modem

  0100
  0200
  39000000
  1f010040
  1b0b0000
  bf000080
  00000000 00000000 00000000 00000000 00000000 00000000
  01000001 00020000 00000000 00000000 00000000

Supplementary services support: 0x000003ff
   Hold / Retrieve
   Terminal Portability
   ECT
   3PTY
   Call Forwarding
   Call Deflection
   MCID
   CCBS

lsmod | grep capi

[root@trixbox112920 asterisk]# lsmod | grep capi
capi                   22913  0
capifs                 10057  2 capi
kernelcapi             49601  3 c4,b1,capi
[root@trixbox112920 asterisk]#

jetzt mal ein paar configs

/etc/capi.conf

c2 c2.bin DSS1 - - - -
c2 - DSS1 - - - -

/etc/asterisk/capi.conf

;
; CAPI config
;
;

; general section

[general]
nationalprefix=0
internationalprefix=00
rxgain=1.0       ;linear receive gain (1.0 = no change)
txgain=1.0       ;linear transmit gain (1.0 = no change)
language=de      ;set default language
;ulaw=yes        ;set this, if you live in u-law world instead of a-law

;jb.....         ;with Asterisk 1.4 you can configure jitterbuffer,
                 ;see Asterisk documentation for all jb* setting available.
;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold.


; interface sections ...

[ISDN1]          ;this example interface gets name 'ISDN1' and may be any
                 ;name not starting with 'g' or 'contr'.
                 ;Use one interface section for each isdn port!
;ntmode=yes      ;if isdn card operates in nt mode, set this to yes
isdnmode=msn     ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
                 ;when using NT-mode, 'DID' should be set in any case
incomingmsn=*    ;allow incoming calls to this list of MSNs/DIDs, * = any
;defaultcid=123  ;set a default caller id to that interface for dial-out,
                 ;this caller id will be used when dial option 'd' is set.
;controller=0    ;ISDN4BSD default
;controller=7    ;ISDN4BSD USB default
controller=1     ;capi controller number of this interface/port
group=1          ;dialout group
;prefix=0        ;set a prefix to calling number on incoming calls
softdtmf=on      ;enable/disable software dtmf detection, recommended for AVM cards
relaxdtmf=on     ;in addition to softdtmf, you can use relaxed dtmf detection
faxdetect=off    ;enable faxdetection and redirection to EXTEN 'fax' for incoming and/or
                 ;outgoing calls. (default='off', possible values: 'incoming','outgoing','both')
accountcode=     ;PBX accountcode to use in CDRs
;amaflags=default;AMA flags for CDR ('default', 'omit', 'billing', or 'documentation')
context=pstn-in  ;context for incoming calls
;holdtype=hold   ;when the PBX puts the call on hold, ISDN HOLD will be used. If
                 ;set to 'local' (default value), no hold is done and the PBX may
                 ;play MOH.
;immediate=yes   ;DID: immediate start of pbx with extension 's' if no digits were
                 ;     received on incoming call (no destination number yet)
                 ;MSN: start pbx on CONNECT_IND and don't wait for SETUP/SENDING-COMPLETE.
                 ;     info like REDIRECTINGNUMBER may be lost, but this is necessary for
                 ;     drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE.
;echosquelch=1   ;_VERY_PRIMITIVE_ echo suppression. Disable this before you start recording voicemail
                 ;or your files may get choppy. (you can use capicommand(echosquelch|no) for this)
;echocancel=yes  ;EICON DIVA SERVER (CAPI) echo cancelation (yes=g165)
                 ;(possible values: 'no', 'yes', 'force', 'g164', 'g165') 
echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)
;echotail=64     ;echo cancel tail setting (default=0 for maximum)
;echocancelnlp=1 ;activate non-linear-processing; this improves echo cancel ratio, but might
                 ;incorporate variable gain in the signal path.
;bridge=yes      ;native bridging (CAPI line interconnect) if available
;callgroup=1     ;PBX call group
;pickupgroup=1   ;PBX pickup group (which call groups are we allowed to pickup)
;transfergroup=1 ;Controller(s) where a transfer on native bridge is allowed to.
;language=de     ;set language for this device (overwrites default language)
;disallow=all    ;RTP codec selection (valid with Eicon DIVA Server only)
;allow=all       ;RTP codec selection (valid with Eicon DIVA Server only)
devices=2        ;number of concurrent calls (b-channels) on this controller
                 ;(2 makes sense for single BRI, 30/23 for PRI/T1)
;jb.....         ;with Asterisk 1.4 you can configure jitterbuffer,
                 ;see Asterisk documentation for all jb* setting available.
;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold.
;qsig=1           ;enable use of Q.SIG extensions. ECMA Variant
;qsig_prnum=1234  ;enable inbound bridging - this should be an QSIG-network-wide unique number

[ISDN2]                   ;this example interface gets name 'ISDN1' and may be any
                              ;name not starting with 'g' or 'contr'.
;ntmode=yes           ;if isdn card operates in nt mode, set this to yes
isdnmode=msn        ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
                              ;when using NT-mode, 'DID' should be set in any case
incomingmsn=*        ;allow incoming calls to this list of MSNs/DIDs, * = any
;defaultcid=123        ;set a default caller id to that interface for dial-out,
                              ;this caller id will be used when dial option 'd' is set.
;controller=0            ;ISDN4BSD default
;controller=7            ;ISDN4BSD USB default
controller=2             ;capi controller number to use
group=1                  ;dialout group
;prefix=0                 ;set a prefix to calling number on incoming calls
softdtmf=on            ;enable/disable software dtmf detection, recommended for AVM cards
relaxdtmf=on          ;in addition to softdtmf, you can use relaxed dtmf detection
accountcode=          ;Asterisk accountcode to use in CDRs
context=pstn-in        ;context for incoming calls
;holdtype=hold        ;when Asterisk puts the call on hold, ISDN HOLD will be used. If
                             ;set to 'local' (default value), no hold is done and Asterisk may
                             ;play MOH.
;immediate=yes      ;DID: immediate start of pbx with extension 's' if no digits were
                             ;     received on incoming call (no destination number yet)
                             ;MSN: start pbx on CONNECT_IND and don't wait for SETUP/SENDING-COMPLETE.
                             ;     info like REDIRECTINGNUMBER may be lost, but this is necessary for
                             ;     drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE.
;echosquelch=1       ;_VERY_PRIMITIVE_ echo suppression
;echocancel=yes      ;EICON DIVA SERVER (CAPI) echo cancelation
                             ;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
echocancelold=yes   ;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)
;echotail=64            ;echo cancel tail setting
;bridge=yes            ;native bridging (CAPI line interconnect) if available
;callgroup=1           ;Asterisk call group
;language=de         ;set language for this device (overwrites default language)
devices=2              ;number of concurrent calls on this controller
                            ;(2 makes sense for single BRI, 30 for PRI)

jetzt mal aus der asterisk console

capi info

trixbox112920*CLI> capi info
Common ISDN API Driver ($Revision: 576 $) www.chan-capi.org
Contr1: 2 B channels total, 2 B channels free.
Contr2: 2 B channels total, 2 B channels free.
trixbox112920*CLI>

capi show channels

trixbox112920*CLI> capi show channels
CAPI B-channel information:
Line-Name       NTmode state i/o bproto isdnstate   ton  number
----------------------------------------------------------------
ISDN2#02         no    -----  -  trans              0x00 ''->''
ISDN2#01         no    -----  -  trans              0x00 ''->''
ISDN1#02         no    -----  -  trans              0x00 ''->''
ISDN1#01         no    -----  -  trans              0x00 ''->''

Es tut mir echt leid das ich euch das Forum hier vollspamme aber ich weiss einfach nichtmehr weiter und bevor ich zu wenig poste gebe ich lieber etwas mehr infos

So dann flamed mich mal