Config Datei vom Hersteller - WLAN automatisch aus

[FRAD]

Hallo,

habe von meinem DSL Lieferanten eine Fritzbox samt USB Stick inkl. Config Datei erhalten.

Meine Frage nun dazu:

1. wird die Config auf dem USB Stick bei jedem Reboot der Box neu aufgespielt?
2. wie kann ich verhindern, das mein WLAN immer automatisch ausgestellt wird?
3. woran kann ich erkennen, ob jemand von extern (Lieferant) auf meine Box zugreifen kann? Muss j awenn auch im Config File definiert sein

Hier meine ausgelesene Config zum Thema WLAN - liegt es evtl. an auto_settings =2, dass mein WLAN imme rautomatisch deaktiviert wird? Zeitschaltuhr ist deaktiviert

wlancfg {
wlancfg_version = 6;
bridge_mode = "bridge-none";
auto_settings = 2;
ap_enabled = 0;
ap_enabled_saved = 1;
ap_enabled_scnd = 0;
ap_enabled_scnd_saved = 1;
channel = 0;
channel_scnd = 0;
channelwidth = 1;
ssid = "test";
ssid_scnd = "test_5GHz";
hidden_ssid = 0;
power_level = 1;
bg_mode = 25;
bg_mode_scnd = 52;
user_isolation = 0;
encryption = 4;
passwd = "";
wep_auth_type = "open";
allowSharedKeyAuth = no;
key_id = 0;
key_value0 = "";
key_len0 = 0;
key_value1 = "";
key_len1 = 0;
key_value2 = "";
key_len2 = 0;
key_value3 = "";
key_len3 = 0;
pskvalue = "xxxxx";
interval = 3600;
turbomode = yes;
wlan_coexistence = 1;
event_control = 6;
WDS_enabled = no;
WDS2_enabled = no;
WDS_hop = 0;
WDS_mac_master = 00:00:00:00:00:00;
WDS_mac_slave0 = 00:00:00:00:00:00;
WDS_mac_slave1 = 00:00:00:00:00:00;
WDS_mac_slave2 = 00:00:00:00:00:00;
WDS_mac_slave3 = 00:00:00:00:00:00;
WDS_encryption = 0;
WDS_key = "";
night_time_control_enabled = no;
night_time_control_no_forced_off = yes;
night_time_control_with_reconnect = yes;
night_time_control_auto_update = no;
guest_ap_enabled = yes;
guest_timeout_active = no;
guest_timeout_minutes = 30;
guest_no_forced_off = no;
guest_ssid = "test_GAST";
guest_encryption = 4;
guest_pskvalue = "xxxxx";
guest_ap_auto_update = yes;
guest_user_isolation = yes;
greenmode_enabled = no;
IPTVoptimize = yes;
wireless_stickandsurf_enabled = no;
tx_autopower = no;
autochannel_plus = no;
autochannel_plus_11a = no;
force_channel_conversion = no;
STA_configured = no;
STA_configured_scnd = no;
STA_enabled = no;
STA_enabled_scnd = no;
STA_ssid = "";
STA_ssid_scnd = "";
STA_mac_master = 00:00:00:00:00:00;
STA_mac_master_scnd = 00:00:00:00:00:00;
STA_encryption = 0;
STA_encryption_scnd = 0;
STA_pskvalue = "";
STA_pskvalue_scnd = "";
STA_key_id = 0;
STA_key_value0 = "";
STA_key_len0 = 0;
STA_key_value1 = "";
STA_key_len1 = 0;
STA_key_value2 = "";
STA_key_len2 = 0;
STA_key_value3 = "";
STA_key_len3 = 0;
STA_mode = 0;
STA_mode_scnd = 52;
STA_overwrite_ap_config = yes;
uapsd_supported = no;
uapsd_enable = no;
wmm_enabled = yes;
wmm_supported = yes;
wmm_ap_aifsn = 10;
wmm_ap_ecwmin = 3;
wmm_ap_ecwmax = 7;
wmm_ap_txop = 1;
wmm_ap_ackpolicy = no;
wmm_sta_aifsn = 10;
wmm_sta_ecwmin = 3;
wmm_sta_ecwmax = 7;
wmm_sta_txop = 1;
wmm_sta_ackpolicy = no;
wps_enable = yes;
wps_mode = 1;
wps_pin = "";
wps_devicename = "FBox";
wps_device_password = xxxx;
wps_uuid = "xxxx";
wps_version = 16;
wps_config_methods_supported = "Keypad,PushButton,Display";
wps_config_methods_enabled = "Keypad,PushButton,Display";
wps_setup_locked_state = "Unlocked";
wps_setup_lock = no;
wps_configuration_state = "Configured";
wps_last_configuration_error = "NoError";
wps_registrar_number_of_entries = 0;
wps_registrar_established = no;
wps_registrar_enable = no;
wps_registrar_uuid = "";
wps_registrar_devicename = "";
wps_guest_uuid = "xxxxxx";
feature_wlan_coexistence = -1;
}

Grüße

 

[chked]

Am einfachsten sieht man diese Einstellungen in der Konfigurationsoberfläche der Fritzbox (Expertenmodus=ein).
Falls der Provider die Einstellungen via Branding deaktiviert hat, hilft evtl. ein Umstellen des Brandings auf AVM.