[Info] [Erfahrungsbericht] Powerline an VDSL 35b: FRITZ!Powerline 1220 vs. devolo Magic 2 – massive Unterschiede bei DSL-Störungen und eine Lösung

Hi

If the VDSL Performer status is 'yes', then I presume your Devolo are communicating with the Fritzbox via TR-064. However, at some point in FritzOS, I remember I had to activate TR-064 (it was as a separate tab), but because I'm on FTTP, I can't see it, or they have deactivated it.

You used to be able to download the support information using the Devolo app for Windows, but I don't know if it's still the case. I remember they tried to retire the Windows app in favour of Android and iOS apps because these days, most use their phones to set up everything.

I'm on the same version of tgc Devolo app for Android, and I use MS Outlook app as my email client. Try setting up a Microsoft email address and use the app to see if you're more successful in getting the Zip file.
 
TR-064 in FritzOS is configurable in Permit Access for Apps in Home Network > Network > Advanced Network Settings

 
Zuletzt bearbeitet:
Thanks for pointing me in the right direction!

I managed to generate a ZIP file using devolo Cockpit 5.2.0.185 under Windows. The DSLCOEXISTENCE entries were indeed present in the .cld files, but Base64-encoded, which explains why my initial text search found nothing.

After decoding the files, I found the following entries on both my Magic 2 adapters (MT2999 and MT3157):

DSLCOEXISTENCE.GENERAL.ENABLE=YES
DSLCOEXISTENCE.GENERAL.RUNNING=YES
DSLCOEXISTENCE.GENERAL.GATEWAY_SUPPORTS_TR064=YES
DSLCOEXISTENCE.GENERAL.GATEWAY_COMPATIBLE=YES
DSLCOEXISTENCE.GENERAL.STATUS_CODE=-231
The diagnostics also report:

  • DSL profile: 35b
  • DSL link status: Up
  • Gateway: Fritzbox
  • DSL information queries: 53 / 43
  • Measurements: 11 / 13
  • DSL disconnections: 0 / 0
  • Target power mask applied: YES / YES
Interestingly, both adapters report mimo_vdsl17a as their configured power mask profile, although the DSL connection uses profile 35b. The available profiles also include mimo_vdsl35b.

This is strong evidence that the adapters are actually obtaining DSL connection information from my FRITZ!Box 7690, rather than merely identifying it as compatible.

Two questions remain:

  1. Do you happen to know what status/error code -231 means?
  2. Is the use of mimo_vdsl17a on a VDSL 35b connection expected behavior?
In any case, thanks again for your help. Without your suggestion to inspect the diagnostic dumps, I would probably never have found this information!
 
Did you change the profile on the Devolo adapters? There's an option to have either Profile 17 or 35. This is done in the Powerline settings of Devolo (I have an English version.) Please note that you would need to do it on *each* Devolo adapter, not just one of them.

Yes, the adapters query the Fritzbox for the SNR margin and, from what I remember, also errors. This influences the operational mode of Devolo adapters.

With Devolo Performer, I found the impact of powerline on my DSL line at the time minimal, if not at all.
 
Thanks for the clarification!

I checked the Powerline settings on my devolo adapters. They are currently configured as follows:

- Automatic compatibility mode: Enabled
- Transmission mode: MIMO
- VDSL profile: 17a (default)

My actual DSL connection uses profile 35b.

According to the description in the devolo web interface, automatic compatibility mode attempts to detect interference and dynamically adjust the transmission power to achieve the best possible performance without disturbing the DSL connection.

This raises an interesting question: Does the manually selected VDSL profile (17a/35b) have any effect while automatic compatibility mode is enabled, or is it only used as a fallback when automatic interference mitigation is disabled or fails?

The diagnostic dumps report "DSLCOEXISTENCE.GENERAL.RUNNING=YES" and "GATEWAY_COMPATIBLE=YES", while the configured power mask remains "mimo_vdsl17a".

So far, my VDSL connection has remained stable, with no CRC errors or errored seconds observed during testing. Cockpit currently reports approximately 341 Mbit/s between the two Magic 2 adapters.

For now, I intend to leave automatic compatibility mode enabled, since it appears to be working well. However, I'm curious whether changing the selected profile to 35b would make any difference while automatic mode is active.
 
I'd presume that all is done automatically and the specific settings are ignored. However, your log files appear to contradict that, unless the adapters are really working within a specific frequency range only (i.e. never go above 35 MHz, but continue operating within the 2-17 MHz range). Devolo calls this a mitigating profile. It's just my speculation because I know very little about the electrical aspect of Devolo working, and I could even be wrong with this speculation.

It'd be interesting if you switched off the automatic profile and selected 'full power' in Devolo adapters (on all of them) to see if this has an impact on errors. I couldn't test that at the time because my DSL line was subject to interference caused by someone else's electrical equipment. My powerline still suffer from the interference even with my FTTP: it shows when the speed between adapters goes down; normally it's between 600-800mbps but when this electrical interference occurs, it goes down to 100mbps, or even 0 Mbps sometimes. I suspect it's a boiler or something similar because it occurs on cold days in the winter.

Normally powerline adapters get a very bad reputation for what they are, and my testing of Netgear ones had confirmed that. However, it shows that superior products like Devolo adapters can successfully be used with DSL lines without causing too many issues. Not so much if you have general interference, but even then, my Fritzbox comes to a halt, so it's not a powerline/non-powerline issue, but a more general issue of impact of interference. At the time, when Openreach engineers (in the UK, Openreach manages the whole telecoms network for all internet service providers) were here to address the issues of my problematic telephone line, they couldn't understand that. However, I now think that they knew where the problem was and just used Devolo as a scapegoat.

I just wish Devolo updated their firmware and introduced more features with it, such as an ability to switch on/off LAN ports, determine the speed of each port to conserve energy (100 Vs 1000mbps) or allow configurable QoS amongst other features.
 
Zuletzt bearbeitet:
Update: devolo Magic 2 – Automatic Compatibility Mode vs. Full Power

Following wg2003's suggestion, I ran another experiment today to see how disabling the automatic compatibility mode affects my VDSL connection.

My setup:

  • FRITZ!Box 7690, VDSL2 profile 35b, full vectoring
  • DSL sync: 144,307 / 42,324 kbit/s
  • Approximate line length: 410 m
  • SNR margin: 6 / 7 dB
  • devolo Magic 2 LAN (MT:2999) and Magic 2 LAN triple (MT:3157)
  • Firmware: 7.12.9.142
I disabled automatic compatibility mode on both devolo adapters and selected full transmission power.

According to devolo Cockpit, the G.hn link rate increased from approximately 341 Mbps to 447 Mbps.

However, the DSL error counters subsequently increased dramatically.

With automatic compatibility mode disabled:

  • Corrected DTUs (last 15 minutes): 439,130
  • Uncorrected DTUs (last 15 minutes): 45
  • CRC errors (last 15 minutes): 20
  • Errored seconds (ES): 120 / 1
  • Severely errored seconds (SES): 3 / 0
Interestingly, DSL synchronization remained unchanged at 144,307 / 42,324 kbit/s, and the SNR margin stayed at 6 / 7 dB.

I then re-enabled automatic compatibility mode on all devolo adapters.

After re-enabling automatic compatibility mode:

  • Corrected DTUs (last 15 minutes): 7,229
  • Uncorrected DTUs (last 15 minutes): 0
  • CRC errors (last 15 minutes): 0
  • Errored seconds (ES): still 120 / 1
  • Severely errored seconds (SES): still 3 / 0
That's a reduction of approximately 98.4% in corrected DTUs, with no additional errored or severely errored seconds recorded.

The minimum effective downstream data rate, which had dropped as low as 131,075 kbit/s during the experiment, subsequently recovered to 142,249 kbit/s.

Conclusion

The results strongly suggest that devolo's automatic compatibility mode is doing a very effective job of reducing interference with my VDSL connection.

What I find particularly interesting is that the substantial increase in DSL errors was not reflected in either the synchronization rate or the reported SNR margin.

Of course, this experiment does not establish whether the improvement is specifically attributable to the TR-064-based VDSL Performer functionality or to other mechanisms within the automatic compatibility mode.

For my particular setup, connection stability is far more important than maximum Powerline throughput. We expect to have three people working from home simultaneously, so DSL interruptions are something I particularly want to avoid.

I'll therefore leave automatic compatibility mode enabled permanently. The additional G.hn link rate simply isn't worth the increased DSL error rate.

Thanks to wg2003 for suggesting the experiment. It turned out to be quite revealing!
 
Interesting, though unsurprising, results.

Changes to SNR margin and consequently speed link can be automatically adjusted by your DSLAM (thanks to DSL Automatic Management System). They don't happen immediately, but over a period of time. A noisy line can have a lot of errors which will result in changes in SNR: the higher the SNR, the less noise on the line. This also depends on whether you're on so called fast path or interleave, and its depth. Fast path offers a higher sync speed and more noise, whereas interleave is for lines that suffer from problems.

However, changes to SNR margin don't have to happen at all, and all depends on how the line is provisioned. For example, for my noisy line, the SNR never went down to 3db as it'd mean more disconnections and less stability overall.

Here's more information on how DSLAM works, though this is for the UK: https://kitz.co.uk/adsl/DLM_system.htm
 
Thanks for the explanation and the link!

That makes sense. I wouldn't expect the DSLAM to react immediately to a relatively short period of increased interference, especially since the connection remained synchronized throughout the experiment.

My FRITZ!Box reports G.INP enabled in both directions, with INP values of 54.0 downstream and 28.5 upstream. That probably helped the line cope with the substantial increase in transmission errors.

What I found particularly interesting was how quickly the error counters responded to the changes in the devolo settings, while both the synchronization rate and SNR margin remained completely unchanged.

With automatic compatibility mode disabled, corrected DTUs reached 439,130 within 15 minutes, accompanied by CRC errors and severely errored seconds. After re-enabling it, corrected DTUs dropped by more than 98%, with no further CRC errors or errored seconds recorded.

So even though the DSLAM hadn't adjusted anything, the difference in line quality was immediately measurable.

For me, the important thing is to avoid sustained interference in the first place rather than relying on DLM or error correction to compensate for it. With three people potentially working from home simultaneously, reliability is considerably more important than squeezing another 100 Mbps out of the Powerline connection.

In any case, this experiment has given me considerably more confidence in devolo's automatic compatibility mode. I'll be leaving it enabled.

Thanks again for suggesting the test!
 

Update: Powerline vollständig entfernt – vier FRITZ!Repeater 6000 im Mesh und DSL-Fehler nahezu verschwunden​

Nach meinen bisherigen Versuchen mit FRITZ!Powerline 1220 und devolo Magic 2 habe ich Powerline inzwischen vollständig aus meinem Netzwerk entfernt. Stattdessen übernehmen jetzt vier FRITZ!Repeater 6000 die WLAN-Versorgung des Hauses.

Das Ergebnis ist bisher in zweierlei Hinsicht erfreulich: Der tatsächliche Netzwerkdurchsatz ist deutlich höher als mit den devolos, und die DSL-Fehlerzähler sind nach deren Entfernung geradezu eingebrochen.

1. Ausgangssituation​

Zur Erinnerung: Ich betreibe eine FRITZ!Box 7690 an einem VDSL2-Anschluss mit Profil 35b und einer Synchronisation von rund 143/42 Mbit/s.

Mit den devolo Magic 2 ließ sich zwar grundsätzlich eine funktionierende Netzwerkverbindung herstellen, allerdings verursachten die Adapter erhebliche Störungen auf der DSL-Leitung.

Besonders deutlich wurde das beim Versuch, den automatischen Kompatibilitätsmodus der devolos zu deaktivieren und die volle Übertragungsleistung zu nutzen.

Dabei stiegen die korrigierten DTU zeitweise auf über 400.000 innerhalb von 15 Minuten. Zusätzlich traten unkorrigierte DTU, CRC-Fehler und Fehlersekunden auf.

Mit aktiviertem Kompatibilitätsmodus beruhigte sich die Situation erheblich. Dennoch lagen die korrigierten DTU weiterhin häufig im Bereich von etwa 6.000 bis 12.000 pro 15 Minuten.

Hinzu kam, dass sich die Powerline-Verbindungen beim Hinzufügen weiterer Adapter zunehmend instabil verhielten. Insbesondere mit einem vierten Adapter kam es zu wiederholten Verbindungsabbrüchen und Neuverhandlungen innerhalb des G.hn-Netzes.

Die tatsächlich gemessenen Übertragungsraten waren ebenfalls wenig beeindruckend.

2. Umstellung auf vier FRITZ!Repeater 6000​

Ich hatte bereits früher versucht, das Haus über WLAN-Mesh zu versorgen. Die Ergebnisse waren damals allerdings ziemlich ernüchternd.

Teilweise wurden völlig ungünstige Funkstrecken gewählt. Ich musste die Topologie manuell korrigieren, damit die Daten über den Repeater im Treppenhaus liefen, anstatt über schlechte direkte Verbindungen zwischen den Etagen.

Inzwischen haben sowohl die FRITZ!Box als auch die Repeater neuere Firmware erhalten. Außerdem habe ich den Aufbau verändert.

Die aktuelle Konfiguration:

  • FRITZ!Box 7690 als Router und Mesh-Master, WLAN deaktiviert
  • FRITZ!Repeater 6000 im Arbeitszimmer als LAN-Brücke, mit 2,5 Gbit/s an der FRITZ!Box angeschlossen
  • FRITZ!Repeater 6000 im Wohnzimmer als WLAN-Brücke zum Arbeitszimmer
  • FRITZ!Repeater 6000 im Esszimmer als WLAN-Brücke zum Wohnzimmer
  • FRITZ!Repeater 6000 im Trainingsraum ebenfalls als WLAN-Brücke zum Wohnzimmer
Damit erfolgt die gesamte WLAN-Versorgung über die vier Tri-Band-Repeater.

Interessanterweise hat sich diese Topologie diesmal vollkommen selbstständig aufgebaut. Ich musste keine einzige Verbindung manuell korrigieren.

3. WLAN-Linkraten und tatsächlicher Durchsatz​

Die Mesh-Übersicht zeigt folgende ausgehandelte Brutto-Linkraten:

FunkstreckeLinkrate
Arbeitszimmer ↔ Wohnzimmerca. 2.300 Mbit/s
Wohnzimmer ↔ Esszimmerca. 1.400 Mbit/s
Wohnzimmer ↔ Trainingsraumca. 906 Mbit/s
Natürlich sind das zunächst nur die WLAN-Linkraten und keine tatsächlichen Nutzdatenraten.

Deshalb habe ich anschließend mit iperf3 einen 60-Sekunden-Test vom Rechner im Esszimmer durchgeführt.

Die Verbindung verlief dabei über:

Esszimmer → Wohnzimmer → Arbeitszimmer → Ethernet → FRITZ!Box-Seite

Es waren also zwei WLAN-Sprünge beteiligt.

Das Ergebnis:

[ ID] Interval Transfer Bitrate
[ 5] 0.00-60.01 sec 1.49 GBytes 213 Mbits/sec sender
[ 5] 0.00-60.05 sec 1.48 GBytes 212 Mbits/sec receiver
Zum Vergleich die zuvor gemessenen Werte mit devolo Magic 2:

MessungTCP-Durchsatz
devolo Magic 2, 1 TCP-Stream101 Mbit/s
devolo Magic 2, 4 TCP-Streams116 Mbit/s
WLAN-Mesh, 2 Funkstrecken, 1 TCP-Stream212 Mbit/s
Das WLAN-Mesh erreicht somit bereits über zwei Funkstrecken ungefähr den doppelten tatsächlichen Durchsatz der bisherigen Powerline-Verbindung.

Für meinen VDSL-Anschluss reicht das vollkommen aus. Entscheidend ist für mich ohnehin eine stabile und flächendeckende Versorgung des Hauses, nicht die höchstmögliche Übertragungsrate.

4. DSL-Fehlerzähler nach Entfernung aller Powerline-Adapter​

Jetzt kommt der für diesen Thread vermutlich interessanteste Teil.

Nachdem sämtliche Powerline-Adapter aus den Steckdosen entfernt waren, zeigte die FRITZ!Box folgende DSL-Werte:

ParameterEmpfangsrichtungSenderichtung
Aktuelle Datenrate142.652 kbit/s42.381 kbit/s
Leitungskapazität146.183 kbit/s42.607 kbit/s
Störabstandsmarge7 dB7 dB
Impulsstörungsschutz (INP)53,028,5
G.INPanan
Fehlersekunden (ES)00
Schwerwiegende Fehlersekunden (SES)00
CRC, letzte 15 Minuten00
Korrigierte DTU, letzte 15 Minuten280
Unkorrigierte DTU, letzte 15 Minuten00
Die Synchronisation liegt weiterhin bei rund 143/42 Mbit/s. Die Störabstandsmarge beträgt in beide Richtungen 7 dB.

Besonders bemerkenswert finde ich die korrigierten DTU.

Mit den devolos im automatischen Kompatibilitätsmodus hatte ich häufig Werte zwischen 6.000 und 12.000 pro 15 Minuten beobachtet.

Ohne Powerline waren es bei der aktuellen Messung gerade einmal 28.

Verglichen mit 12.000 entspricht das einem Rückgang um rund 99,8 %.

Die Anzeige der korrigierten DTU pro Minute lag bei dieser Momentaufnahme allerdings noch bei 107,3. Die unterschiedlichen Zeitfenster der Zähler sind deshalb zu berücksichtigen. Für den Vergleich verwende ich ausdrücklich den angezeigten 15-Minuten-Wert.

Selbstverständlich ist eine einzelne Messung noch kein Langzeitnachweis. Allerdings passt dieser drastische Rückgang sehr gut zu den vorherigen Beobachtungen, insbesondere zu den gezielten Versuchen mit aktiviertem und deaktiviertem Powerline-Kompatibilitätsmodus.

5. Warum funktioniert das WLAN-Mesh plötzlich so viel besser?​

Das ist für mich fast genauso interessant wie die DSL-Werte.

Bei meinen ersten WLAN-Versuchen waren sowohl die Übertragungsraten als auch die automatisch gewählte Mesh-Topologie deutlich schlechter.

Diesmal haben die Geräte sofort eine vernünftige Kaskade aufgebaut und liefern wesentlich bessere Ergebnisse.

Geändert haben sich insbesondere:

  • Die Firmware der FRITZ!Box 7690
  • Die Firmware der FRITZ!Repeater 6000
  • Die Netzwerktopologie mit einem zentralen, per LAN angebundenen Tri-Band-Repeater
  • Teilweise die Positionierung und die verwendeten Funkstrecken
Welche Firmware-Versionen beim ersten Versuch installiert waren, weiß ich leider nicht mehr.

Deshalb kann ich nicht beurteilen, ob AVM zwischenzeitlich die automatische Auswahl der Mesh-Verbindungen verbessert hat oder ob die geänderte Topologie den entscheidenden Unterschied ausmacht.

Auffällig ist jedenfalls, dass ich diesmal überhaupt nicht manuell eingreifen musste.

6. Vorläufiges Fazit​

Die vier FRITZ!Repeater 6000 haben zusammen rund 880 € gekostet. Das ist zwar keine Kleinigkeit, aber angesichts der bisherigen Ergebnisse erscheint mir die Investition durchaus gerechtfertigt.

Ich habe jetzt:

  • Eine deutlich bessere WLAN-Abdeckung
  • Höheren tatsächlichen Netzwerkdurchsatz als mit Powerline
  • Eine automatisch aufgebaute, sinnvolle Mesh-Topologie
  • Keine Powerline-Adapter mehr im Stromnetz
  • Bei der ersten Messung ohne Powerline nur noch 28 korrigierte DTU innerhalb von 15 Minuten statt zuvor häufig mehrerer Tausend
Für mich ist insbesondere der letzte Punkt entscheidend. Im Haus wird regelmäßig im Homeoffice gearbeitet, teilweise von mehreren Personen gleichzeitig. Eine stabile DSL-Verbindung ist daher wesentlich wichtiger als theoretisch hohe Powerline-Datenraten.

Mein bisheriges Fazit lautet deshalb: Powerline hat sich in meiner Installation nicht bewährt. Das WLAN-Mesh funktioniert inzwischen erheblich besser und scheint gleichzeitig das DSL-Störungsproblem weitgehend beseitigt zu haben.

Ich werde die Konfiguration jetzt einige Tage unverändert laufen lassen und insbesondere die DSL-Fehlerzähler weiter beobachten.

Sollten sich die niedrigen Fehlerwerte dauerhaft bestätigen, wäre das für mich ein ziemlich eindeutiges Ergebnis.
 
  • Like
Reaktionen: Masur28
Das ist mal ein ausführlicher Erfahrungsbericht, aber ich habe eine Frage zu einem (meist) gar nicht beachteten Detail, der mich als Elektriker bei Netzwerkproblemem regelmäßig beschäftigt: Welche Patchkabel kamen während der Powerline-Versuche zum Einsatz - geschirmte oder ungeschirmte?

Ich frage, weil die Rx- und Tx-Adernpaare beidseitig auf Koppler aufgeschaltet werden, die die LAN-Kabel galvanisch von den aktiven Komponenten beider Geräte trennt. Der Schirm stellt aber eine elektrische Verbindung zwischen zwei Geräten dar und bietet die Möglichkeit, daß von einem Gerät Störpotentiale auf das andere Gerät übertragen werden können.
 
Zum Teil kamen die mit den FRITZ!Repeatern 6000 mitgelieferten Patchkabel zum Einsatz, daneben verschiedene bereits vorhandene Kabel. Auf vielen davon ist nicht einmal eine Spezifikation aufgedruckt. Ob die Kabel geschirmt oder ungeschirmt waren, kann ich daher nicht zuverlässig sagen.

Der angesprochene Kopplungsweg ist sicherlich interessant. Allerdings ist Powerline inzwischen vollständig aus meinem Netzwerk verschwunden. Das WLAN-Mesh funktioniert erheblich besser, und die DSL-Fehler sind drastisch zurückgegangen.

Weitere Versuchsreihen werde ich deshalb nicht mehr durchführen. Für mich ist das Problem gelöst.
 
Detailed report indeed. I also wanted to point out that Fritz powerline adapters do not use the same technology as Devolo. Therefore, if you were to test the impact of VDSL Performer and how well it works in communicating through the TR protocol with the Fritzbox, you should have removed Fritz adapters from your local network. Also, don't Fritz adapters use AV2 as standard whereas Magic adapters G.Hn as their technology? These are different standards.
 
You're absolutely right that FRITZ!Powerline 1220 uses HomePlug AV2, whereas devolo Magic 2 uses G.hn. These are different and incompatible standards.

However, I did not operate both systems simultaneously. The FRITZ!Powerline adapters had already been removed before I started testing the devolo Magic 2 adapters.

The tests with VDSL Performer enabled and disabled were therefore conducted exclusively with devolo Magic 2 devices.

What I cannot establish from these tests is how much of the improvement was specifically attributable to the TR-064 communication with the FRITZ!Box, as opposed to the compatibility settings themselves.

The comparison between the two Powerline technologies was intended to document their respective effects on my VDSL 35b connection, not to suggest that they use the same transmission standard.
 
Kostenlos!

Statistik des Forums

Themen
249,057
Beiträge
2,309,845
Mitglieder
378,865
Neuestes Mitglied
collegebyo